M0116MY-161LSBR2-1 Newhaven Display, M0116MY-161LSBR2-1 Datasheet
M0116MY-161LSBR2-1
Specifications of M0116MY-161LSBR2-1
Related parts for M0116MY-161LSBR2-1
M0116MY-161LSBR2-1 Summary of contents
Page 1
... User’s Guide M0116MY-161LSBR2-1 VFD- (Vacuum Fluorescent Display Module) For product support, contact Newhaven Display International RoHS Compliant Newhaven Display International 2511 Technology Drive, #101 Elgin, IL 60124 Tel: (847) 844-8795 Fax: (847) 844-8796 February 28, 2008 ...
Page 2
... STANDARD SPECIFICATION FOR APPROVAL NAME 1. SCOPE This specification applies to VFD module (Model No: M0116MY-161LSB2- FEATURES 2.1 Simple connection to the host system data bus via four-wire clocked serial interface. 2.2 Since a DC/DC converter is used, only +5Vdc power source is required to operate the module. 2.3 One chip controller offers integral 64 16 bit programmable logic array, low power consumption and high reliability in services ...
Page 3
STANDARD SPECIFICATION FOR APPROVAL NAME 4.3 Specification of Display Panel Parameter Display Size (W*H) Number of Digit Character Size (W*H) Display Color 4.4 Environment Conditions Parameter Operating Temperature Storage Temperature Humidity (Operating) Humidity (Non-operating) Vibration (10 55Hz) Shock 4.5 Absolute ...
Page 4
STNDARD SPECIFICATION FOR APPROVAL NAME 4.8 Timing Chart 4.8.1 SCLK and DATA Timing SCLK DATA Fig-1. SCLK and Serial DATA Timing Diagram 4.8.2 Data word LSB/MSB Timing Prior Data Word (LSB Last) D2 DATA 4.9 Signal Interfacing Pin # Signal ...
Page 5
STNDARD SPECIFICATION FOR APPROVAL NAME 4.10 System Block Diagram Vcc Rupx3 Vcc / (+5Vdc 4.11 Outer Dimensions 16 SCLK DATA VDD -Vdis Controller ...
Page 6
STNDARD SPECIFICATION FOR APPROVAL NAME 5. FUNCTIONS The module has control data, display data write and reset functions. Input data from the host system is loaded into the module’s display buffer via the serial data input channel as 8-bit serial ...
Page 7
STNDARD SPECIFICATION FOR APPROVAL NAME 5.1.1 Buffer Pointer Control This command changes the display contents only at an arbitrary digit. (The RAM write address is set.) The digit position to be modified is represented by the value of D3 D0. ...
Page 8
STNDARD SPECIFICATION FOR APPROVAL NAME 5.1.3 Brightness Control This command sets the brightness of the VFD. This command allows the brightness to be adjusted by 1/32 step. As shown in Table-12, the test value ranges from 0 to 31. Brightness ...
Page 9
STNDARD SPECIFICATION FOR APPROVAL NAME Character Font Table DOCUMENT NO. REV.NO 1.0 Table-14 PAGE 8/10 ...
Page 10
STNDARD SPECIFICATION FOR APPROVAL NAME 5.3 RESET The reset function allows the users to re-initialize the alphanumeric display controller, while the power is still applied to the module, by applying a logical “0” to pin #5 and pin #7(/RST) of ...
Page 11
... Noise may affect the interface signal and cause improper operation important to keep the length of the interface cable less than 50cm. 6.11 Since all VFD modules contain C-MOS ICs, anti-static handling procedures are always required. NOTE: Newhaven Display reserves the right to change or modify this existing specification and or product in order to improve the quality of this design. DOCUMENT NO. ...