MT18VDDF6472G-40BG3 Micron Technology Inc, MT18VDDF6472G-40BG3 Datasheet - Page 4
![no-image](/images/manufacturer_photos/0/4/441/micron_technology_inc_sml.jpg)
MT18VDDF6472G-40BG3
Manufacturer Part Number
MT18VDDF6472G-40BG3
Description
MODULE SDRAM DDR 512MB 184DIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18VDDF12872Y-40BF1.pdf
(31 pages)
Specifications of MT18VDDF6472G-40BG3
Memory Type
DDR SDRAM
Memory Size
512MB
Speed
400MT/s
Package / Case
184-DIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Table 5:
Pin numbers may not correlate with symbol; refer to Pin Assignment Tables for pin number and symbol information.
pdf: 09005aef80f6b913, source: 09005aef80f6b41c
DDAF18C64_128x72G.fm - Rev. C 9/04 EN
27, 29, 32, 37, 41, 43, 48,
78, 86, 97, 107, 119, 129,
115,
5, 14, 25, 36, 47, 56, 67,
44, 45, 49, 51, 134, 135,
140, 149, 159, 169, 177
PIN NUMBERS
118, 122, 125, 130,
63, 65, 154
137, 138
142, 144
52, 59
157
141
10
21
Pin Descriptions
WE#, CAS#, RAS#
DQS0–DQS17
CK0, CK0#
SYMBOL
BA0, BA1
CB0–CB7
A0–A12
RESET#
CKE0
S0#
Output
Output
Input/
Input/
TYPE
Input
Input
Input
Input
Input
Input
Input
Asynchronously forces all registered ouputs LOW when RESET#
is LOW. This signal can be used during power-up to ensure CKE
is LOW and DQs are High-Z.
Command Inputs: RAS#, CAS#, and WE# (along with S#) define
the command being entered.
Clock: CK, CK# are differential clock inputs. All address and
control input signals are sampled on the crossing of the positive
edge of CK,and negative edge of CK#. Output data (DQ and
DQS) is referenced to the crossings of CK and CK#.
Clock Enable: CKE HIGH activates and CKE LOW deactivates the
internal clock, input buffers and output drivers. Taking CKE
LOW provides PRECHARGE POWER-DOWN and SELF REFRESH
operations (all device banks idle), or ACTIVE POWER-DOWN
(row ACTIVE in any device bank). CKE is synchronous for
POWER-DOWN entry and exit, and for SELF REFRESH entry. CKE
is asynchronous for SELF REFRESH exit and for disabling the
outputs. CKE must be maintained HIGH throughout read and
write accesses. Input buffers (excluding CK, CK# and CKE) are
disabled during POWER-DOWN. Input buffers (excluding CK,
CK# and CKE) are disabled during POWER-DOWN. Input buffers
(excluding CKE) are disabled during SELF REFRESH. CKE is an
SSTL_2 input but will detect an LVCMOS LOW level after V
applied and until CKE is first brought HIGH. After CKE is
brought HIGH, it becomes an SSTL_2 input only.
Chip Selects: S# enables (registered LOW) and disables
(registered HIGH) the command decoder. All commands are
masked when S# is registered HIGH. S# is considered part of the
command code.
Bank Address: BA0 and BA1 define to which device bank an
ACTIVE, READ, WRITE, or PRECHARGE command is being
applied.
Address Inputs: Provide the row address for ACTIVE commands,
and the column address and auto precharge bit (A10) for READ/
WRITE commands, to select one location out of the memory
array in the respective device bank. A10 sampled during a
PRECHARGE command determines whether the PRECHARGE
applies to one device bank (A10 LOW, device bank selected by
BA0, BA1) or all device banks (A10 HIGH). The address inputs
also provide the op-code during a MODE REGISTER SET
command. BA0 and BA1 define which mode register (mode
register or extended mode register) is loaded during the LOAD
MODE REGISTER command.
Data Strobe: Output with READ data, input with WRITE data.
DQS is edge-aligned with READ data, centered in WRITE data.
Used to capture data.
Check Bits.
4
512MB, 1GB (x72, ECC, SR) PC3200
Micron Technology, Inc., reserves the right to change products or specifications without notice.
184-PIN DDR SDRAM RDIMM
DESCRIPTION
©2004 Micron Technology, Inc. All rights reserved.
DD
is