MT18VDDF12872HG-40BD1 Micron Technology Inc, MT18VDDF12872HG-40BD1 Datasheet - Page 8
![MODULE DDR SDRAM 1GB 200-SODIMM](/photos/7/83/78349/mfg_mt_sodimm_series_sml.jpg)
MT18VDDF12872HG-40BD1
Manufacturer Part Number
MT18VDDF12872HG-40BD1
Description
MODULE DDR SDRAM 1GB 200-SODIMM
Manufacturer
Micron Technology Inc
Datasheet
1.MT18VDDF12872HY-40BF1.pdf
(26 pages)
Specifications of MT18VDDF12872HG-40BD1
Memory Type
DDR SDRAM
Memory Size
1GB
Speed
200MHz
Package / Case
200-SODIMM
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
557-1116
Burst Length
burst oriented, with the burst length being program-
mable, as shown in Figure 4, Mode Register Definition
Diagram. The burst length determines the maximum
number of column locations that can be accessed for a
given READ or WRITE command. Burst lengths of 2, 4,
or 8 locations are available for both the sequential and
the interleaved burst types.
operation or incompatibility with future versions may
result.
of columns equal to the burst length is effectively
selected. All accesses for that burst take place within
this block, meaning that the burst will wrap within the
block if a boundary is reached. The block is uniquely
selected by A1–Ai when the burst length is set to two,
by A2–Ai when the burst length is set to four and by
A3–Ai when the burst length is set to eight (where Ai is
the most significant column address bit for a given
configuration. See Note 5 of Table 6, Burst Definition
Table, on page 9, for Ai values). The remaining (least
significant) address bit(s) is (are) used to select the
starting location within the block. The programmed
burst length applies to both read and write bursts.
Burst Type
to be either sequential or interleaved; this is referred to
as the burst type and is selected via bit M3.
mined by the burst length, the burst type and the start-
ing column address, as shown in Table 6, Burst
Definition Table, on page 9.
Read Latency
between the registration of a READ command and the
availability of the first bit of output data. The latency
can be set to 2, 2.5, or 3clocks, as shown in Figure 5,
CAS Latency Diagram, on page 9.
pdf: 09005aef80e4880c, source: 09005aef80e487d7
DDAF18C128x72HG.fm - Rev. A 10/04 EN
Read and write accesses to DDR SDRAM devices are
Reserved states should not be used, as unknown
When a READ or WRITE command is issued, a block
Accesses within a given burst may be programmed
The ordering of accesses within a burst is deter-
The READ latency is the delay, in clock cycles,
8
and the latency is m clocks, the data will be available
nominally coincident with clock edge n + m. The CAS
Latency Table indicates the operating frequencies at
which each CAS latency setting can be used.
operation or incompatibility with future versions may
result.
* M14 and M13 (BA1 and BA0)
must be “0, 0” to select the
base mode register (vs. the
extended mode register).
If a READ command is registered at clock edge n,
Reserved states should not be used as unknown
0*
Figure 4: Mode Register Definition
14
BA1 BA0
0*
Micron Technology, Inc., reserves the right to change products or specifications without notice.
13
12
A12 A11
1GB (x72, ECC, DR) PC3200
Operating Mode
M13
11
0
0
-
10
A10
M12 M11
0
0
-
9
A9
200-PIN DDR SODIMM
0
0
-
8
A8
M10
0
0
-
Diagram
7
A7 A6 A5 A4 A3
M9
M6
0
0
-
CAS Latency BT
0
0
0
0
1
1
1
1
6
M8 M7
0
1
M5
-
0
0
1
1
0
0
1
1
5
0
0
-
M4
0
1
0
1
0
1
0
1
4
M3
M6-M0
0
1
Valid
Valid
3
-
Burst Length
M2
CAS Latency
0
0
0
0
1
1
1
1
2
A2 A1 A0
Reserved
Reserved
Reserved
Reserved
Reserved
M1
0
0
1
1
0
0
1
1
Operating Mode
Normal Operation
Normal Operation/Reset DLL
All other states reserved
1
2.5
2
3
M0
©2004 Micron Technology, Inc.
0
1
0
1
0
1
0
1
0
Interleaved
Burst Type
Sequential
Burst Length
Reserved
Reserved
Reserved
Reserved
Reserved
Mode Register (Mx)
M3 = 0
Address Bus
2
4
8