EEC2E305HQA401 Nichicon, EEC2E305HQA401 Datasheet - Page 3

• Manufacturer Part Number: EEC2E305HQA401
• Description: CAP 3.0UF 250V METL PP AC POWR
• Manufacturer: Nichicon
• Series: ECr

Specifications of EEC2E305HQA401

• Capacitance: 3.0µF
• Voltage - Ac: 250V
• Dielectric Material: Polypropylene, Metallized
• Tolerance: -5%, +10%
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Chassis Mount
• Package / Case: Rectangular Box
• Size / Dimension: 1.457" L x 0.453" W (37.00mm x 11.50mm)
• Height: 0.984" (25.00mm)
• Termination: Quick Connect, Disconnect
• Features: General Purpose
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Esr (equivalent Series Resistance): -
• Voltage - Dc: -
• Other names: 493-3778

PLASTIC FILM CAPACITORS
( 3 )
3. In the equipment
( 1 )
( 2 )
( 3 )
4. Maintenance and Inspection
( 1 )
5. In an Emergency
( 1 )
6. Storage
( 1 )
( 2)
7. Disposal
( 1 )
8. Other
( 1 )
( 2 )
( 3 )
The above mentioned material is according to EIAJ RCR2350 B (issued in July 2002) titled "Guideline of notabilia for Fixed Plastic Film
Capacitors for use in Electronic Equipment". Please refer to the book for details.
Cleaning
q If it is necessary to use cleaning agents to wash the board after soldering, please select alcohol based agents such as
w Please wash the board as soon as possible after soldering.
e Please dry the board as soon as possible after cleaning.
Do not directly touch the terminal with your hand.
Do not short between terminals be conductor, nor spill conductible liquid such as alkaline nor acidic solution on or near the
capacitor.
Please make sure that the ambient conditions where the set is installed will be free from spilling water or oil, direct sunlight,
ultraviolet rays, radiation, poisonous gas, vibration or mechanical shock.
If periodical inspection is required, please inspect the capacitor based on the specification of the drawings or catalog.
If you see or smell smoke, immediately turn off the main switch or pull out the plug from the outlet.
Storage
q Do not store the capacitor in high temperature or high humidity. The ambient storage conditions should be:
w Please store the capacitors in the original packed condition to avoid any physical stress to the capacitor.
Handling
q Do not apply excess vibration, mechanical shock (drop) or pressure to the capacitor.
w Do not apply stress to the lead such as bending, pulling or twisting.
Please dispose capacitors as industrial waste.
Contents of this catalog (specifications, material, etc.) are subject to change without notice.
Technical information (data) contained in this material is for description representation and application of the product and does not
constitute any guarantee.
When ordering, please include the following information:
q Voltage to be applied ("DC" or "AC", ripple value)
w Rated capacitance value and rated capacitance tolerance
e Category temperature range (inherent temperature + radiant heat should be inclued)
r Specific operating condition (wave form, effective current, dv/dt, etc.)
y Soldering condition (pre-heat condition, solder temperature, time, profile when chip parts are mounted on the same board)
u Set ambient condition (max. operating temperature, method of affixing, automobile use, existence of any
Do not use parts provided as samples in sets for resale.
t Estimated failure mode
isopropyl alcohol.
Ambient conditions to avoid;
ultraviolet rays, radiation, poisonous gas such as
hydrogen sulfide, sulfurous acid, nitrous acid, chorine,
ammonium, etc..
If the capacitor should fail, what effect will this have on the components or set.
If other components should fail, what effect will it have on the capacitor.
gas surrounding capacitor)
Temperature : --10
Humidity
Place
quick temperature change
Exposure to spilling water or oil, direct sunlight,
: lower than 75%
: indoor
to +
40°C
CAT.8100Z