EEC2E305HQA401 Nichicon, EEC2E305HQA401 Datasheet - Page 2

• Manufacturer Part Number: EEC2E305HQA401
• Description: CAP 3.0UF 250V METL PP AC POWR
• Manufacturer: Nichicon
• Series: ECr

Specifications of EEC2E305HQA401

• Capacitance: 3.0µF
• Voltage - Ac: 250V
• Dielectric Material: Polypropylene, Metallized
• Tolerance: -5%, +10%
• Operating Temperature: -25°C ~ 85°C
• Mounting Type: Chassis Mount
• Package / Case: Rectangular Box
• Size / Dimension: 1.457" L x 0.453" W (37.00mm x 11.50mm)
• Height: 0.984" (25.00mm)
• Termination: Quick Connect, Disconnect
• Features: General Purpose
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Spacing: -
• Esr (equivalent Series Resistance): -
• Voltage - Dc: -
• Other names: 493-3778

PLASTIC FILM CAPACITORS
( 8 )
( 9 )
( 10 ) When designing circuit boards, please take into consideration how other parts would be affected should
2. Mounting
( 1 )
( 2 )
Table 2 Derating of Voltage at High Frequency
Fig 2 Solder temp. and soldering time
Frequency
50/60 (Hz)
360
340
320
300
280
260
240
220
001k
005k
010k
020k
030k
040k
050k
060k
070k
080k
090k
100k
Permissible Current, VA value and Inherent Temperature Rise
q Do not use film capacitors in circuits that may exceed the maximum permissible current as specified in tables 3 to 8. The
w The permissible VA value is restricted by the upper category temperature(ambient temperature + inherent temperature +
e The inherent temperature under a no air flow shall be within the value listed below.
A "hum" may be produced under certain high frequency wave conditions. The "hum" does not effect the capacitor characteristics.
Please consult our sales office if your application does not permit a "hum".
the capacitor develop a short or open circuit.
Installation
q When installing capacitors, you must avoid any pulling, pushing or twisting stress to the leads or terminals.
w Certain coditions, such as large capacitor body size or serious vibration, require the capacitor body to be affixed to the board
Soldering
q When soldering capacitors, avoid proesses that require a long dwell time or high temperatures. Such conditions will result in
w When using a soldering iron to solder the capacitor, the soldering condition must be within the following specifications:
e If re-work is necessary, please wait until the capacitor temperature is equal to room temperature. Do not re-work more than
r Please do not use Infrared-reflow an it will cause serious heat stress to the capacitor.
t Prior to soldering film capacitors on the same PC board as chip type capacitors, please consult our sales office to confirm the
XK
permissible current will values will vary due to material and design, even though appearance is similar, therefore, please
carefully confirm all perimeters using the specification.
Also, if the capacitors to be subjected to a sinuous wave flow, please contact our sales office to select the proper capacitor.
radiant heat).
Do not use the capacitor in circuits which exceed the maximum permissible VA value specified in table 3 to 8. The permissible
values will vary due to material and design, even though appearance is similar, therefore, please carefully confirm all
perimeters using the specification.
Also, if the capacitors to be subjected to a sinuous wave flow, please contact our sales office to select the proper capacitor.
XK
XP, XT series ........... + 5°C or below
using holders or resin coating. When using such materials, please be sure they do not effect the capacitor characteristics.
deterioration of characteristics or short-circuit defects. Please ensure that the soldering process is within the range shown in
the following Fig. 2.
twice.
compatibility of the soldering process.
1
-(ZH)
Bit temperature: 350
Application time of soldering iron : 3 second
-(ZH)
2
Derating Rate to
50/60Hz AC Rated voltage
, XK Series
, XK series ...... + 10°C or below
3
Soldering Time (Sec.)
100 (%)
4
54
39
34
30
27
26
25
24
23
22
21
21
5
6
7
±
Frequency
50/60 (Hz)
10°C
Preheat shall be less than 1 minute at a
8
temperature lower than 110 C
001k
005k
010k
020k
030k
040k
050k
060k
070k
080k
090k
100k
9
In case soldering iron in used.
In case of solder dipping.
10
XP Series
Derating Rate to
50/60Hz AC Rated voltage
100 (%)
76
55
49
41
38
36
35
33
32
31
30
30
CAT.8100Z