HCPL-2602#300 Avago Technologies US Inc., HCPL-2602#300 Datasheet - Page 9

• Manufacturer Part Number: HCPL-2602#300
• Description: OPTOCOUPLER LINE RX 8-SMD GW
• Manufacturer: Avago Technologies US Inc.
• Type: Line Receiverr

Specifications of HCPL-2602#300

• Package / Case: 8-SMD Gull Wing
• Voltage - Isolation: 3750Vrms
• Input Type: AC, DC
• Voltage - Supply: 4.5 V ~ 5.5 V
• Operating Temperature: 0°C ~ 70°C
• Mounting Type: Surface Mount
• Isolation Voltage: 3750 Vrms
• Maximum Continuous Output Current: 50 mA
• Maximum Fall Time: 10 ns
• Maximum Forward Diode Current: 60 mA
• Maximum Rise Time: 24 ns
• Output Device: Integrated Photo IC
• Configuration: 1 Channel
• Maximum Baud Rate: 10 MBps
• Maximum Forward Diode Voltage: 2.7 V
• Maximum Reverse Diode Voltage: 0.95 V
• Maximum Power Dissipation: 40 mW
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Number Of Elements: 1
• Output Type: Open Collector
• Baud Rate: 10Mbps
• Forward Voltage: 2.7V
• Forward Current: 60mA
• Output Current: 50mA
• Package Type: PDIP SMD
• Operating Temp Range: 0C to 70C
• Power Dissipation: 40mW
• Propagation Delay Time: 75ns
• Pin Count: 8
• Mounting: Surface Mount
• Reverse Breakdown Voltage: 0.95V
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Contains lead / RoHS non-compliant

Notes:
10. No external pull up is required for a high logic state on the enable input. If the V
11. In accordance with UL 1577, each optocoupler is proof tested by applying an insulation test voltage of 4500 for one second (leakage detection
12. t
13. See application section titled “Propagation Delay, Pulse-Width Distortion and Propagation Delay Skew” for more information.
Figure 1. Typical high level output current vs.
temperature.
Figure 4. Typical output voltage vs. forward
input current.
9
1. Bypassing of the power supply line is required, with a 0.1 F ceramic disc capacitor adjacent to each optocoupler as illustrated in Figure 15. Total
2. Device considered a two terminal device: pins 1, 2, 3, and 4 shorted together, and pins 5, 6, 7, and 8 shorted together.
3. The t
4. The t
5. The t
6. The t
7. CM
8. CM
9. For sinusoidal voltages,
15
10
lead length between both ends of the capacitor and the isolator pins should not exceed 20 mm.
output pulse.
output pulse.
of the output pulse.
of the output pulse.
performance.
current limit, I
range.
6
3
2
1
0
5
0
5
4
PSK
-60
0
I
F
H
L
is equal to the worst case difference in t
– FORWARD INPUT CURRENT – mA
is the maximum tolerable rate of fall of the common mode voltage to assure that the output will remain in a low logic state (i.e., V
PLH
PHL
ELH
EHL
is the maximum tolerable rate of rise of the common mode voltage to assure that the output will remain in a high logic state (i.e., V
-40
|dv
––––––
1
propagation delay is measured from the 3.75 mA point on the falling edge of the input pulse to the 1.5 V point on the rising edge of the
propagation delay is measured from the 3.75 mA point on the rising edge of the input pulse to the 1.5 V point on the falling edge of the
enable propagation delay is measured from the 1.5 V point on the falling edge of the enable input pulse to the 1.5 V point on the rising edge
enable propagation delay is measured from the 1.5 V point on the rising edge of the enable input pulse to the 1.5 V point on the falling edge
T
dt
A
CM
-20
– TEMPERATURE – °C
|
i-o
2
max
0
5 A).
R
20
R
3
= f
L
L
R
= 350
= 1 K
L
40
= 4 K
CM
4
V
V
V
I
V
I
T
CC
O
E
V
= 250 µA
CM
60
A
CC
= 2 V
= 5.5 V
= 25 °C
= 5.5 V
(p-p)
5
= 5 V
80
100
6
PHL
Figure 2. Typical low level output voltage vs.
temperature.
Figure 5. Typical low level output current vs.
temperature.
and/or t
0.4
0.3
0.2
0.1
0.5
60
50
40
20
70
-60
-60
V
V
V
PLH
CC
E
OL
-40
-40
= 2 V
that will be seen between units at any given temperature within the operating condition
= 0.6 V
T
= 5 V
T
A
A
-20
-20
– TEMPERATURE – °C
– TEMPERATURE – °C
I
I
O
O
= 12.8 mA
0
0
= 9.6 mA
20
20
40
40
I
I
I
E
I
V
V
I
I
= 10-15 mA
I
I
O
O
pin is not used, tying V
= 5.0 mA
CC
E
60
60
= 5 mA
= 6.4 mA
= 16 mA
= 2 V
= 5.5 V
80
80
100
100
Figure 3. Typical input characteristics.
E
2.6
2.4
2.2
2.0
1.8
1.6
1.4
1.2
1.0
to V
0
CC
will result in improved CMR
10
I
I
– INPUT CURRENT – mA
20
30
40
0°C
25°C
70°C
OUT
OUT
< 0.8 V).
50
> 2.0 V).
60