HCPL-4200-300E Avago Technologies US Inc., HCPL-4200-300E Datasheet - Page 10
![OPTOCOUPLER 20MA LOOP 8-SMD GW](/photos/22/84/228410/4176142_sml.jpg)
HCPL-4200-300E
Manufacturer Part Number
HCPL-4200-300E
Description
OPTOCOUPLER 20MA LOOP 8-SMD GW
Manufacturer
Avago Technologies US Inc.
Type
Receiverr
Datasheet
1.HCPL-4200500.pdf
(13 pages)
Specifications of HCPL-4200-300E
Voltage - Isolation
3750Vrms
Input Type
DC
Voltage - Supply
4.5 V ~ 20 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-SMD Gull Wing
No. Of Channels
1
Optocoupler Output Type
Logic Gate
Input Current
24mA
Output Voltage
20V
Opto Case Style
SMD
No. Of Pins
8
Peak Reflow Compatible (260 C)
Yes
Isolation Voltage
3.75kV
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
HCPL-4200-300E
Manufacturer:
AVAGO
Quantity:
5 000
Part Number:
HCPL-4200-300E
Manufacturer:
AVAGO/安华高
Quantity:
20 000
Figure 16. Test Circuit for Common Mode Transient Immunity.
Figure 14. Typical Logic High Enable Propagation Delay vs. Temperature.
Applications
Data transfer between equipment which employs cur-
rent loop circuits can be accomplished via one of three
configurations: simplex, half duplex or full duplex com-
munication. With these configurations, point-to-point
and multidrop arrange ments are possible. The appropri-
ate configuration to use depends upon data rate, num-
ber of stations, number and length of lines, direction of
data flow, protocol, current source location and voltage
compliance value, etc.
Simplex
The simplex configuration, whether point to point or
multi drop, gives unidirectional data flow from transmit-
ter to receiver(s). This is the simplest configuration for use
in long line length (two wire), for high data rate, and low
current source compliance level applications. Block dia-
grams of simplex point-to-point and multidrop arrange-
ments are given in Figures 17a and 17b respectively for
the HCPL-4200 receiver optocoupler.
10
200
150
100
50
0
-60
-40
-20
T
A
– TEMPERATURE –°C
0
C
L
t
t
= 15 pF
PHZ
PZH
20
40
60
4.5 V
4.5 V
V
20 V
20 V
CC
80
100
Figure 15. Typical Logic Low Enable Propagation Delay vs. Temperature.
For the highest data rate per formance in a current loop,
the configuration of a non-isolated active transmitter
(containing current source) transmitting data to a re-
mote isolated receiver(s) should be used. When the cur-
rent source is located at the trans mitter end, the loop is
charged approximately to V
the current source is located at the receiver end, the loop
is charged to the full compliance voltage level. The lower
the charged voltage level the faster the data rate will be.
In the configurations of Figures 17a and 17b, data rate is
independent of the current source voltage compliance
level. An adequate compliance level of current source
must be available for voltage drops across station(s) dur-
ing the MARK state in multi drop applications or for long
line length. The maximum compliance level is deter-
mined by the trans mitter breakdown characteristic.
100
80
60
40
20
0
-60
-40
-20
T
A
– TEMPERATURE –°C
0
C
L
= 15 pF
t
t
PLZ
PZL
20
40
60
4.5 V
4.5 V
V
20 V
20 V
MI
CC
80
(2.5 V). Alternatively, when
100