HCPL-4506 Avago Technologies US Inc., HCPL-4506 Datasheet
HCPL-4506
Specifications of HCPL-4506
Available stocks
Related parts for HCPL-4506
HCPL-4506 Summary of contents
Page 1
... Minimized Pulse Width Distortion PWD = 450 ns • 15 kV/µs minimum common mode transient immu- nity • CTR > 44 • Safety approval: UL Recognized -3750 V rms / 1 min. for HCPL-4506/0466/J456 -5000 V rms / 1 min. for HCPL-4506 Option 020 and HCNW4506 CSA Approved IEC/EN/DIN EN 60747-5-2 Approved ...
Page 2
... Selection Guide Standard Package 8-Pin DIP Type (300 Mil) Part HCPL-4506 Number IEC/EN/DIN V = 630 Vpeak IORM EN 60747- (Option 060) 5-2 Approval *Technical data for these products are on separate Avago publications. 2 White Mold 8-Pin DIP Small Outline (300 Mil) SO8 HCPL-J456 HCPL-0466 ...
Page 3
... To order, choose a part number from the part number column and combine with the desired option from the option column to form an order entry. Example 1: HCPL-4506-560E to order product of 300 mil DIP Gull Wing Surface Mount package in Tape and Reel packaging with IEC/EN/DIN EN 60747-5-2 Safety Approval and RoHS compliant. Example 2: HCPL-4506 to order product of 300 mil DIP package in Tube packaging and non RoHS compliant ...
Page 4
... TYPE NUMBER A XXXXZ YYWW 1 2 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) HCPL-4506 Gull Wing Surface Mount Option 300 Outline Drawing 9.65 ± 0.25 (0.380 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± ...
Page 5
... TYPE NUMBER A XXXXZ R YYWW 1.19 (0.047) MAX. 3.56 ± 0.13 (0.140 ± 0.005) 1.080 ± 0.320 (0.043 ± 0.013) HCPL-J456 Gull Wing Surface Mount Option 300 Outline Drawing 9.80 ± 0.25 (0.386 ± 0.010 1.19 (0.047) MAX. 1.080 ± 0.320 (0.043 ± 0.013) 2 ...
Page 6
... HCPL-0466 Outline Drawing (8-Pin Small Outline Package XXX 3.937 ± 0.127 YWW (0.155 ± 0.005 PIN ONE 0.406 ± 0.076 (0.016 ± 0.003) * 5.080 ± 0.127 (0.200 ± 0.005) 3.175 ± 0.127 (0.125 ± 0.005) * TOTAL PACKAGE LENGTH (INCLUSIVE OF MOLD FLASH) 5.207 ± ...
Page 7
HCNW4506 Gull Wing Surface Mount Option 300 Outline Drawing 11.15 ± 0.15 (0.442 ± 0.006 1.78 ± 0.15 (0.070 ± 0.006) 2.54 (0.100) BSC DIMENSIONS IN MILLIMETERS (INCHES). LEAD COPLANARITY = 0.10 mm (0.004 ...
Page 8
Solder Reflow Temperature Profile 300 PREHEATING RATE 3 ° °C/–0.5 °C/SEC. REFLOW HEATING RATE 2.5 °C ± 0.5 °C/SEC. 200 160 °C 150 °C 140 °C 3 ° °C/–0.5 °C 100 ROOM TEMPERATURE ...
Page 9
... Minimum Internal 0.08 Plastic Gap (Internal Clearance) Minimum Internal NA Tracking (Internal Creepage) Tracking Resistance CTI ≥175 (Comparative Tracing Index) Isolation Group IIIa 9 HCPL-4506 HCPL-J456 UL 1577 • Component • Acceptance Notice #5 DIN VDE 0884 • (June 1992) • Value HCPL-J456 HCPL-0466 HCNW4506 7 ...
Page 10
... There are recommended techniques such as grooves and ribs which may be used on a printed circuit board to achieve desired creepage and clearances. Creepage and clearance distances will also change depending on fac- tors such as pollution degree and insulation level. HCPL-0466 HCPL-4506 Symbol Option 060 Option 060 I-IV I-IV ...
Page 11
... Resistor Voltage (Pin 7) Output Voltage (Pin 6-5) Supply Voltage (Pin 8-5) [3] Output Power Dissipation [4] Total Power Dissipation Lead Solder Temperature (HCPL-4506, HCPL-J456) Lead Solder Temperature (HCNW4506) Infrared and Vapor Phase Reflow Temperature (HCPL-0466 and Option 300) Recommended Operating Conditions Parameter Symbol ...
Page 12
... HCPL-0466 HCNW4506 HCPL-J456 0 0.6 CCH 0.6 CCL V HCPL-4506 1.5 F HCPL-0466 HCPL-J456 1.2 1.6 HCNW4506 1.6 /∆T HCPL-4506 -1 HCPL-0466 HCPL-J456 HCNW4506 -1.3 HCPL-4506 5 R HCPL-0466 HCPL-J456 3 HCNW4506 C HCPL-4506 60 IN HCPL-0466 HCPL-J456 72 HCNW4506 /∆T 0.014 0.8 V† Max. Units Test Conditions % ...
Page 13
... Any 2 Parts Output High Level |CM Common Mode Transient Immunity Output Low Level |CM Common Mode Transient Immunity Power Supply PSR Rejection *All typical values at 25° † 0.8 V for HCPL-J456, HCNW4506. F(off ) mA, V F(on) F(off ) Min. Typ.* Max. Units 30 200 400 480 100 ...
Page 14
... Typ.* Max. HCPL-4506 3750 HCPL-0466 HCPL-J456 3750 HCPL-4506 5000 Option020 HCNW4506 5000 12 HCPL-4506 10 HCPL-J456 HCPL-0466 12 13 HCNW4506 10 10 HCPL-4506 0.6 HCPL-0466 HCPL-J456 0.8 HCNW4506 0.5 > 3.0 V). O < 1.0 V for any given device. PHL PLH Units Test Conditions Fig. V rms RH < 50 min 25° ...
Page 15
... V F – 1.0 0.1 0.01 0.001 1.10 1.20 1.30 1.40 1.50 1.60 V – FORWARD VOLTAGE – VOLTS F Figure 4. HCPL-4506 and HCPL-0466 input cur- rent vs. forward voltage. HCPL-4506 fig kΩ I =10 mA F(ON – SHIELD *TOTAL LOAD CAPACITANCE Figure 6. Propagation delay test circuit. ...
Page 16
... V – SUPPLY VOLTAGE – Figure 12. Propagation delay vs. supply voltage. HCPL-4506 fig ∆ SWITCH SWITCH HCPL-4506 fig 11b 800 100 pF 600 °C A 400 200 100 RL – LOAD RESISTANCE – kΩ Figure 10. Propagation delay vs. load resistance. HCPL-4506 fig 14 500 t PLH t ...
Page 17
... V OUT 100 pF 5 *100 pF TOTAL CAPACITANCE 310 Ω 3 CMOS 4 SHIELD Figure 18. LED drive circuit with resistor connected to LED anode (not recommended). HCPL-4506 fig 22-new 150 175 1 20 kΩ C LEDP LEDN 4 SHIELD Figure 16. Optocoupler input to output capacitance HCPL-4506 fig 20-new model for unshielded optocouplers. ...
Page 18
... Figure 22. AC Equivalent circuit for Figure 21 during common mode transients kΩ C LEDP C 2 LED02 7 C LED01 V C OUT LEDN CLEDN* ** – SHIELD /dt TRANSIENTS. CM < V DURING +dV /dt (OFF HCPL-4506 fig 24-new kΩ C LEDP LED02 C LED01 V C OUT LEDN CLEDN SHIELD /dt TRANSIENTS HCPL-4506 fig 26-new 20 kΩ 100 pF 20 kΩ 100 pF ...
Page 19
... V CC1 20 kΩ V OUT1 HCPL-4506 V CC2 HCPL-4506 20 kΩ HCPL-4506 V OUT2 HCPL-4506 HCPL-4506 HCPL-4506 fig 28 I LED1 V OUT1 V OUT2 I LED2 Q1 OFF PHL MIN. NOTE: THE PROPAGATION DELAYS USED TO CALCULATE THE MAXIMUM DEAD TIME ARE TAKEN AT EQUAL TEMPERATURES. Figure 26. Waveforms for dead time calculation. ...
Page 20
... Without a detector shield, the dominant cause of op- tocoupler CMR failure is capacitive coupl-ing from the input side of the optocoupler, through the package, to the detector IC as shown in Figure 16. The HCPL-4506 series improve CMR performance by using a detector IC with an optically transparent Faraday shield, which diverts the capacitively coupled current away from the sensitive IC circuitry ...
Page 21
... This delay is the maximum value for the propaga- tion delay difference specification which is specified at 450 ns for the HCPL-4506 series over an operating tem- perature range of -40°C to 100°C. Delaying the LED signal by the maximum propagation ...