LT1370HVCR Linear Technology, LT1370HVCR Datasheet - Page 7

IC SWTCHNG REG 6A HI-EFF 7-DD

LT1370HVCR

Manufacturer Part Number
LT1370HVCR
Description
IC SWTCHNG REG 6A HI-EFF 7-DD
Manufacturer
Linear Technology
Type
Step-Down (Buck), Step-Up (Boost), Inverting, Cuk, Flyback, Forward Converterr
Datasheet

Specifications of LT1370HVCR

Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
1.25 ~ 42 V
Current - Output
6A
Frequency - Switching
500kHz
Voltage - Input
2.7 ~ 25 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
D²Pak, TO-263 (7 leads + tab)
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-

Available stocks

Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LT1370HVCR#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LT1370HVCR#TRPBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
APPLICATIO S I FOR ATIO
OPERATION
Unique error amplifier circuitry allows the LT1370 to
directly regulate negative output voltages. The negative
feedback amplifier’s 100k source resistor is brought out
for negative output voltage sensing. The NFB pin regulates
at – 2.48V while the amplifier output internally drives the
FB pin to 1.245V. This architecture, which uses the same
main error amplifier, prevents duplicating functions and
maintains ease of use. Consult LTC Marketing for units
that can regulate down to – 1.25V.
The error signal developed at the amplifier output is
brought out externally. This pin (V
Positive Output Voltage Setting
The LT1370 develops a 1.245V reference (V
FB pin to ground. Output voltage is set by connecting the
FB pin to an output resistor divider (Figure 1). The FB pin
bias current represents a small error and can usually be
ignored for values of R2 up to 7k. The suggested value for
R2 is 6.19k. The NFB pin is normally left open for positive
output applications. Positive fixed voltage versions are
available (consult LTC Marketing).
Negative Output Voltage Setting
The LT1370 develops a – 2.48V reference (V
NFB pin to ground. Output voltage is set by connecting the
NFB pin to an output resistor divider (Figure 2). The
–30µA NFB pin bias current (I
voltage errors and should not be ignored. This has been
accounted for in the formula in Figure 2. The suggested
value for R2 is 2.49k. The FB pin is normally left open for
negative output applications.
Dual Polarity Output Voltage Sensing
Certain applications benefit from sensing both positive
and negative output voltages. One example is the “Dual
Output Flyback Converter with Overvoltage Protection”
circuit shown in the Typical Applications section. Each
output voltage resistor divider is individually set as
described above. When both the FB and NFB pins are used,
U
U U
NFB
C
W
) can cause output
) has three different
NFR
REF
) from the
) from the
U
functions. It is used for frequency compensation, current
limit adjustment and soft starting. During normal regula-
tor operation this pin sits at a voltage between 1V (low
output current) and 1.9V (high output current). The error
amplifier is a current output (g
be externally clamped for lowering current limit. Like-
wise, a capacitor coupled external clamp will provide soft
start. Switch duty cycle goes to zero if the V
below the control pin threshold, placing the LT1370 in an
idle mode.
the LT1370 acts to prevent either output from going
beyond its set output voltage. For example, in this applica-
tion if the positive output were more heavily loaded than
the negative, the negative output would be greater and
would regulate at the desired set-point voltage. The posi-
tive output would sag slightly below its set-point voltage.
This technique prevents either output from going unregu-
lated high at no load.
NFB
PIN
Figure 2. Negative Output Resistor Divider
Figure 1. Positive Output Resistor Divider
V
NFR
PIN
FB
I
V
NFB
REF
–V
OUT
R1
R2
V
OUT
–V
R1 =
R1
R2
OUT
( ) (
2.48
m
V
= V
R1 = R2
R2
OUT
) type, so this voltage can
⏐V
NFB
= V
OUT
+ 30 • 10
( )
1 +
REF
(
⏐– 2.48
1.245
V
OUT
R1
R2
( )
LT1370 • F01
1 +
– 6
– 1
+ I
R1
R2
)
NFB
)
C
pin is pulled
LT1370
(R1)
LT1370 • F02
sn1370 1370fs
7

Related parts for LT1370HVCR