LTC1625IGN Linear Technology, LTC1625IGN Datasheet - Page 6

• Manufacturer Part Number: LTC1625IGN
• Description: IC SW REG STEP-DOWN SYNC 16-SSOP
• Manufacturer: Linear Technology
• Type: Step-Down (Buck)r

Specifications of LTC1625IGN

• Internal Switch(s): No
• Synchronous Rectifier: Yes
• Number Of Outputs: 1
• Voltage - Output: 1.19 ~ 36 V
• Current - Output: 50mA
• Frequency - Switching: 150kHz
• Voltage - Input: 3.7 ~ 36 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 16-SSOP
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant
• Power - Output: -

PIN
LTC1625
EXTV
voltage is above 4.7V, the switch closes and supplies
INTV
SYNC (Pin 2): Synchronization Input for Internal Oscilla-
tor. The oscillator will nominally run at 150kHz when open,
225kHz when tied above 1.2V, and will lock over a 1.5:1
clock frequency range.
RUN/SS (Pin 3): Run Control and Soft Start Input. A
capacitor to ground at this pin sets the ramp time to full
current output (approximately 1s/ F). Forcing this pin
below 1.4V shuts down the device.
FCB (Pin 4): Forced Continuous Input. Tie this pin to
ground to force synchronous operation at low load, to a
resistive divider from the secondary output when using
a secondary winding, or to INTV
operation at low load.
I
current comparator threshold increases with this control
voltage. Nominal voltage range for this pin is 0V to 2.4V.
SGND (Pin 6): Signal Ground. Connect to the (–) terminal
of C
V
from the remotely sensed output voltage or from an
external resistive divider across the output.
V
V
a 3.3V output and V
6
TH
OSENSE
PROG
OSENSE
U
(Pin 5): Error Amplifier Compensation Point. The
OUT
CC
CC
FUNCTIONS
.
power from EXTV
(Pin 8): Output Voltage Programming. When
(Pin 1): INTV
is connected to the output, V
(Pin 7): Output Voltage Sense. Feedback input
U
U
PROG
CC
Switch Input. When the EXTV
CC
. Do not exceed 7V at this pin.
> 3.5V selects a 5V output.
CC
to enable Burst Mode
PROG
< 0.8V selects
CC
Leaving V
an external resistive divider between the output and
V
PGND (Pin 9): Driver Power Ground. Connects to the
source of the bottom N-channel MOSFET, the (–) terminal
of C
BG (Pin 10): Bottom Gate Drive. Drives the gate of the
bottom N-channel MOSFET between ground and INTV
INTV
driver and control circuits are powered from this voltage.
Decouple this pin to power ground with a minimum of
4.7 F tantalum capacitance.
BOOST (Pin 12): Topside Floating Driver Supply. The (+)
terminal of the bootstrap capacitor connects here. This pin
swings from a diode drop below INTV
TG (Pin 13): Top Gate Drive. Drives the top N-channel
MOSFET with a voltage swing equal to INTV
diode drop, superimposed on the switch node voltage.
SW (Pin 14): Switch Node. The (–) terminal of the boot-
strap capacitor connects here. This pin swings from a
diode drop below ground up to V
TK (Pin 15): Top MOSFET Kelvin Sense. MOSFET V
sensing requires this pin to be routed to the drain of the top
MOSFET separately from V
V
ground with an RC filter (4.7 , 0.1 F) for applications
above 3A.
OSENSE
IN
VCC
(Pin 16): Main Supply Input. Decouple this pin to
CC
and the (–) terminal of C
.
(Pin 11): Internal 5.2V Regulator Output. The
PROG
open allows the output voltage to be set by
IN
.
IN
IN
.
.
CC
to V
IN
CC
+ INTV
minus a
CC
CC
DS
.
.