LTC3736EGN Linear Technology, LTC3736EGN Datasheet - Page 12
![IC CTRLR SW SYNC DUAL 2PH 24SSOP](/photos/6/59/65961/161-24-ssop_sml.jpg)
LTC3736EGN
Manufacturer Part Number
LTC3736EGN
Description
IC CTRLR SW SYNC DUAL 2PH 24SSOP
Manufacturer
Linear Technology
Series
PolyPhase®r
Type
Step-Down (Buck)r
Datasheet
1.LTC3736EGNPBF.pdf
(28 pages)
Specifications of LTC3736EGN
Internal Switch(s)
No
Synchronous Rectifier
Yes
Number Of Outputs
2
Voltage - Output
0.6 ~ 9.8 V
Current - Output
1A
Frequency - Switching
550kHz ~ 750kHz
Voltage - Input
2.75 ~ 9.8 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
24-SSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Power - Output
-
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
LTC3736EGN
Manufacturer:
Linear Technology
Quantity:
135
Company:
Part Number:
LTC3736EGN
Manufacturer:
ST
Quantity:
766
Part Number:
LTC3736EGN
Manufacturer:
LT/凌特
Quantity:
20 000
Part Number:
LTC3736EGN#PBF
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3736EGN-2
Manufacturer:
LINEAR/凌特
Quantity:
20 000
Part Number:
LTC3736EGN-2#PBF
Manufacturer:
ADI/亚德诺
Quantity:
20 000
OPERATIO
LTC3736
Dropout Operation
When the input supply voltage (V
the output voltage, the rate of change of the inductor
current while the external P-channel MOSFET is on (ON
cycle) decreases. This reduction means that the P-channel
MOSFET will remain on for more than one oscillator cycle
if the inductor current has not ramped up to the threshold
set by the EAMP on the I
input supply voltage will eventually cause the P-channel
MOSFET to be turned on 100%; i.e., DC. The output
voltage will then be determined by the input voltage minus
the voltage drop across the P-channel MOSFET and the
inductor.
Undervoltage Lockout
To prevent operation of the external MOSFETs below safe
input voltage levels, an undervoltage lockout is incorporated
in the LTC3736. When the input supply voltage (V
below 2.3V, the external P- and N-channel MOSFETs and
all internal circuitry are turned off except for the undervolt-
age block, which draws only a few microamperes.
Peak Current Sense Voltage Selection and Slope
Compensation (IPRG1 and IPRG2 Pins)
When a controller is operating below 20% duty cycle, the
peak current sense voltage (between the SENSE
pins) allowed across the external P-channel MOSFET is
determined by:
where A is a constant determined by the state of the IPRG
pins. Floating the IPRG pin selects A = 1; tying IPRG to V
selects A = 5/3; tying IPRG to SGND selects A = 2/3. The
maximum value of V
maximum sense voltage allowed across the external
P-channel MOSFET is 125mV, 85mV or 204mV for the
three respective states of the IPRG pin. The peak sense
voltages for the two controllers can be independently
selected by the IPRG1 and IPRG2 pins.
However, once the controller’s duty cycle exceeds 20%,
slope compensation begins and effectively reduces the
12
∆
V
SENSE MAX
(
)
U
=
A V
(Refer to Functional Diagram)
ITH
(
ITH
is typically about 1.98V, so the
TH
10
– . 0 7
pin. Further reduction in the
V
IN
)
) decreases towards
+
IN
and SW
) drops
IN
peak sense voltage by a scale factor given by the curve in
Figure 1.
The peak inductor current is determined by the peak sense
voltage and the on-resistance of the external P-channel
MOSFET:
Power Good (PGOOD) Pin
A window comparator monitors both feedback voltages
and the open-drain PGOOD output pin is pulled low when
either or both feedback voltages are not within ±10% of
the 0.6V reference voltage. PGOOD is low when the
LTC3736 is shut down or in undervoltage lockout.
2-Phase Operation
Why the need for 2-phase operation? Until recently, con-
stant frequency dual switching regulators operated both
controllers in phase (i.e., single phase operation). This
means that both topside MOSFETs (P-channel) are turned
on at the same time, causing current pulses of up to twice
the amplitude of those from a single regulator to be drawn
from the input capacitor. These large amplitude pulses
increase the total RMS current flowing in the input capaci-
tor, requiring the use of larger and more expensive input
capacitors, and increase both EMI and power losses in the
input capacitor and input power supply.
I
PK
=
Figure 1. Maximum Peak Current vs Duty Cycle
∆
110
100
V
90
80
70
60
50
40
30
20
10
0
SENSE MAX
R
0
DS ON
10
(
(
20
)
30
)
DUTY CYCLE (%)
40
50
60
70
80
90
3736 F01
100
3736fa