LM2597M-12/NOPB National Semiconductor, LM2597M-12/NOPB Datasheet - Page 9
![IC REG SIMPLE SWITCHER 8-SOIC](/photos/7/60/76085/lm2597m-12_nopb_sml.jpg)
LM2597M-12/NOPB
Manufacturer Part Number
LM2597M-12/NOPB
Description
IC REG SIMPLE SWITCHER 8-SOIC
Manufacturer
National Semiconductor
Series
SIMPLE SWITCHER®r
Type
Step-Down (Buck)r
Datasheet
1.LM2597M-3.3NOPB.pdf
(34 pages)
Specifications of LM2597M-12/NOPB
Internal Switch(s)
Yes
Synchronous Rectifier
No
Number Of Outputs
1
Voltage - Output
12V
Current - Output
500mA
Frequency - Switching
150kHz
Voltage - Input
4.5 ~ 40 V
Operating Temperature
-40°C ~ 125°C
Mounting Type
Surface Mount
Package / Case
8-SOIC (3.9mm Width)
Supply Voltage Range
4.5V To 40V
Termination Type
SMD
Driver Case Style
NSOIC
No. Of Pins
8
Output Voltage Min
1.23V
Voltage Regulator Type
Buck Switching
Rohs Compliant
Yes
Filter Terminals
SMD
Input Voltage Primary Max
40V
Leaded Process Compatible
Yes
No. Of Outputs
1
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Power - Output
-
Other names
*LM2597M-12
*LM2597M-12/NOPB
LM2597M-12
*LM2597M-12/NOPB
LM2597M-12
Given:
V
V
I
1. Inductor Selection (L1)
A. Select the correct inductor value selection guide from
Figure 3 , Figure 4 , or Figure 5 . (Output voltages of 3.3V, 5V, or
12V respectively.) For all other voltages, see the design pro-
cedure for the adjustable version.
B. From the inductor value selection guide, identify the induc-
tance region intersected by the Maximum Input Voltage line
and the Maximum Load Current line. Each region is identified
by an inductance value and an inductor code (LXX).
C. Select an appropriate inductor from the four manufacturer’s
part numbers listed in Figure 7 .
2. Output Capacitor Selection (C
A. In the majority of applications, low ESR (Equivalent Series
Resistance) electrolytic capacitors between 82 µF and 220 µF
and low ESR solid tantalum capacitors between 15 µF and
100 µF provide the best results. This capacitor should be
located close to the IC using short capacitor leads and short
copper traces. Do not use capacitors larger than 220 µF.
For additional information, see section on output capaci-
tors in application information section.
B. To simplify the capacitor selection procedure, refer to the
quick design component selection table shown in Figure 1 .
This table contains different input voltages, output voltages,
and load currents, and lists various inductors and output
capacitors that will provide the best design solutions.
C. The capacitor voltage rating for electrolytic capacitors
should be at least 1.5 times greater than the output voltage,
and often much higher voltage ratings are needed to satisfy
the low ESR requirements for low output ripple voltage.
D. For computer aided design software, see Switchers Made
Simple
LM2597/LM2597HV Series Buck Regulator Design Procedure (Fixed
Output)
LOAD
OUT
IN
(max) = Maximum DC Input Voltage
(max) = Maximum Load Current
= Regulated Output Voltage (3.3V, 5V or 12V)
PROCEDURE (Fixed Output Voltage Version)
®
version 4.1 or later).
OUT
)
9
Given:
V
V
I
1. Inductor Selection (L1)
A. Use the inductor selection guide for the 5V version shown
in Figure 4 .
B. From the inductor value selection guide shown in Figure 4 ,
the inductance region intersected by the 12V horizontal line
and the 0.4A vertical line is 100 µH, and the inductor code is
L20.
C. The inductance value required is 100 µH. From the table in
Figure 7 , go to the L20 line and choose an inductor part
number from any of the four manufacturers shown. (In most
instance, both through hole and surface mount inductors are
available.)
2. Output Capacitor Selection (C
A. See section on output capacitors in application infor-
mation section.
B. From the quick design component selection table shown in
Figure 1 , locate the 5V output voltage section. In the load
current column, choose the load current line that is closest to
the current needed in your application, for this example, use
the 0.5A line. In the maximum input voltage column, select the
line that covers the input voltage needed in your application,
in this example, use the 15V line. Continuing on this line are
recommended inductors and capacitors that will provide the
best overall performance.
The capacitor list contains both through hole electrolytic and
surface mount tantalum capacitors from four different capaci-
tor manufacturers. It is recommended that both the manufac-
turers and the manufacturer’s series that are listed in the table
be used.
In this example aluminum electrolytic capacitors from several
different manufacturers are available with the range of ESR
numbers needed.
C. For a 5V output, a capacitor voltage rating at least 7.5V or
more is needed. But, in this example, even a low ESR,
switching grade, 120 µF 10V aluminum electrolytic capacitor
would exhibit approximately 400 m of ESR (see the curve in
Figure 17 for the ESR vs voltage rating). This amount of ESR
would result in relatively high output ripple voltage. To reduce
the ripple to 1% of the output voltage, or less, a capacitor with
a higher voltage rating (lower ESR) should be selected. A 16V
or 25V capacitor will reduce the ripple voltage by approxi-
mately half.
LOAD
OUT
IN
(max) = 12V
120 µF 25V Panasonic HFQ Series
120 µF 25V Nichicon PL Series
(max) = 0.4A
= 5V
EXAMPLE (Fixed Output Voltage Version)
OUT
)
www.national.com