ISL6333IRZ Intersil, ISL6333IRZ Datasheet - Page 39
![IC CTRLR PWM 3PHASE BUCK 48-QFN](/photos/18/29/182944/48-vqfn_l48_sml.jpg)
ISL6333IRZ
Manufacturer Part Number
ISL6333IRZ
Description
IC CTRLR PWM 3PHASE BUCK 48-QFN
Manufacturer
Intersil
Datasheet
1.ISL6333ACRZ.pdf
(40 pages)
Specifications of ISL6333IRZ
Applications
Controller, Intel VR11
Voltage - Input
5 ~ 12 V
Number Of Outputs
1
Voltage - Output
0.5 ~ 1.6 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
48-VQFN
Number Of Pwm Outputs
3
On/off Pin
Yes
Adjustable Output
Yes
Topology
Buck
Switching Freq
80 TO 1000kHz
Operating Supply Voltage (max)
5.25V
Output Current
100000A
Output Voltage
0.5 to 1.6V
Synchronous Pin
No
Rise Time
26ns
Fall Time
18ns
Operating Temperature Classification
Industrial
Mounting
Surface Mount
Pin Count
48
Package Type
QFN EP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
The power components should be placed first, which includes
the MOSFETs, input and output capacitors, and the inductors. It
is important to have a symmetrical layout for each power train,
preferably with the controller located equidistant from each.
Symmetrical layout allows heat to be dissipated equally across
all power trains. Equidistant placement of the controller to the
power trains it controls through the integrated drivers helps
keep the gate drive traces equally short, resulting in equal trace
impedances and similar drive capability of all sets of MOSFETs.
When placing the MOSFETs, try to keep the source of the
upper FETs and the drain of the lower FETs as close as
thermally possible. Input bulk capacitors should be placed
close to the drain of the upper FETs and the source of the lower
FETs. Locate the output inductors and output capacitors
between the MOSFETs and the load. The high-frequency input
and output decoupling capacitors (ceramic) should be placed
as close as practicable to the decoupling target, making use of
the shortest connection paths to any internal planes, such as
vias to GND next or on the capacitor solder pad.
The critical small components include the bypass capacitors
for VCC and PVCC, and many of the components
surrounding the controller including the feedback network
and current sense components. Locate the VCC/PVCC
bypass capacitors as close to the controller as possible. It is
especially important to locate the components associated
with the feedback circuit close to their respective controller
pins, since they belong to a high-impedance circuit loop,
sensitive to EMI pick-up.
A multi-layer printed circuit board is recommended. Figure 30
shows the connections of the critical components for the
converter. Note that capacitors C
each represent numerous physical capacitors. Dedicate one
solid layer, usually the one underneath the component side of
the board, for a ground plane and make all critical component
ground connections with vias to this layer.
Dedicate another solid layer as a power plane and break this
plane into smaller islands of common voltage levels. Keep the
metal runs from the PHASE terminal to output inductors short.
The power plane should support the input power and output
power nodes. Use copper filled polygons on the top and bottom
circuit layers for the phase nodes. Use the remaining printed
circuit layers for small signal wiring.
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
For information regarding Intersil Corporation and its products, see www.intersil.com
39
xx(IN)
ISL6333, ISL6333A, ISL6333B, ISL6333C
and C
xx(OUT)
could
Routing UGATE, LGATE, and PHASE Traces
Great attention should be paid to routing the UGATE, LGATE,
and PHASE traces since they drive the power train MOSFETs
using short, high current pulses. It is important to size them as
large and as short as possible to reduce their overall
impedance and inductance. They should be sized to carry at
least one ampere of current (0.02” to 0.05”). Going between
layers with vias should also be avoided, but if so, use two vias
for interconnection when possible.
Extra care should be given to the LGATE traces in particular
since keeping their impedance and inductance low helps to
significantly reduce the possibility of shoot-through. It is also
important to route each channels UGATE and PHASE traces
in as close proximity as possible to reduce their inductances.
Current Sense Component Placement and Trace
Routing
One of the most critical aspects of the controller regulator
layout is the placement of the inductor DCR current sense
components and traces. The R-C current sense components
must be placed as close to their respective ISEN+ and
ISEN- pins on the controller as possible.
The sense traces that connect the R-C sense components to
each side of the output inductors should be routed on the
bottom of the board, away from the noisy switching
components located on the top of the board. These traces
should be routed side by side, and they should be very thin
traces. It’s important to route these traces as far away from
any other noisy traces or planes as possible. These traces
should pick up as little noise as possible.
Thermal Management
For maximum thermal performance in high current, high
switching frequency applications, connecting the thermal
GND pad of the controllers to the ground plane with multiple
vias is recommended. This heat spreading allows the part to
achieve its full thermal potential. It is also recommended
that the controllers be placed in a direct path of airflow if
possible to help thermally manage the part.
October 8, 2010
FN6520.3