ISL6334ACRZ Intersil, ISL6334ACRZ Datasheet - Page 22
![IC CTRLR PWM 4PHASE BUCK 40-QFN](/photos/6/88/68851/40-qfn_pkg_sml.jpg)
ISL6334ACRZ
Manufacturer Part Number
ISL6334ACRZ
Description
IC CTRLR PWM 4PHASE BUCK 40-QFN
Manufacturer
Intersil
Datasheet
1.ISL6334ACRZ.pdf
(30 pages)
Specifications of ISL6334ACRZ
Applications
Controller, Intel VR11.1
Voltage - Input
3 ~ 12 V
Number Of Outputs
1
Voltage - Output
0.5 ~ 1.6 V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
40-VFQFN, 40-VFQFPN
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
ISL6334ACRZ
Manufacturer:
INTERSIL
Quantity:
250
Part Number:
ISL6334ACRZ
Manufacturer:
INTERSIL
Quantity:
20 000
Part Number:
ISL6334ACRZ-T
Manufacturer:
INTERSIL
Quantity:
20 000
Overcurrent Protection
ISL6334, ISL6334A has two levels of overcurrent protection.
Each phase is protected from a sustained overcurrent
condition by limiting its peak current, while the combined
phase currents are protected on an instantaneous basis.
In instantaneous protection mode, ISL6334, ISL6334A
utilizes the sensed average current I
overcurrent condition. See “Channel-Current Balance” on
page 15 for more details on how the average current is
measured. The average current is continually compared with
a constant 105µA reference current, as shown in Figure 10.
Once the average current exceeds the reference current, a
comparator triggers the converter to shutdown.
The current out of IMON pin is equal to the sensed average
current I
at IMON will be proportional to the sensed average current
and the resistor value. The ISL6334, ISL6334A continuously
monitors the voltage at IMON pin. If the voltage at IMON pin
is higher than 1.11V, a comparator triggers the overcurrent
shutdown. By increasing the resistor between IMON and
GND, the overcurrent protection threshold can be adjusted
to be less than 105µA. For example, the overcurrent
threshold for the sensed average current I
95µA by using a 11.8k
At the beginning of overcurrent shutdown, the controller
places all PWM signals in a high-impedance state within
20ns, commanding the Intersil MOSFET driver ICs to turn off
both upper and lower MOSFETs. The system remains in this
state a period of 4096 switching cycles. If the controller is still
enabled at the end of this wait period, it will attempt a
soft-start. If the fault remains, the trip-retry cycles will
continue indefinitely (as shown in Figure 11) until either
controller is disabled or the fault is cleared. Note that the
energy delivered during trip-retry cycling is much less than
during full-load operation, so there is no thermal hazard
during this kind of operation.
FIGURE 11. OVERCURRENT BEHAVIOR IN HICCUP MODE.
0A
0V
AVG
. With a resistor from IMON to GND, the voltage
F
SW
OUTPUT CURRENT
OUTPUT VOLTAGE
= 500kHz
Ω
resistor from IMON to GND.
2ms/DIV
22
AVG
to detect an
AVG
can be set to
ISL6334, ISL6334A
For the individual channel overcurrent protection, ISL6334,
ISL6334A continuously compares the sensed current signal
of each channel with the 129µA reference current. If one
channel current exceeds the reference current, ISL6334,
ISL6334A will pull PWM signal of this channel to low for the
rest of the switching cycle. This PWM signal can be turned
on next cycle if the sensed channel current is less than the
129µA reference current. The peak current limit of individual
channel will not trigger the converter to shutdown.
Thermal Monitoring (VR_HOT/VR_FAN)
There are two thermal signals to indicate the temperature
status of the voltage regulator: VR_HOT and VR_FAN. Both
VR_FAN and VR_HOT pins are open-drain outputs, and
external pull-up resistors are required. Those signals are
valid only after the controller is enabled.
The VR_FAN signal indicates that the temperature of the
voltage regulator is high and more cooling airflow is needed.
The VR_HOT signal can be used to inform the system that
the temperature of the voltage regulator is too high and the
CPU should reduce its power consumption. The VR_HOT
signal may be tied to the CPU’s PROC_HOT signal.
The diagram of thermal monitoring function block is shown in
Figure 12. One NTC resistor should be placed close to the
power stage of the voltage regulator to sense the operational
temperature, and one pull-up resistor is needed to form the
voltage divider for the TM pin. As the temperature of the power
stage increases, the resistance of the NTC will reduce, resulting
in the reduced voltage at the TM pin. Figure 13 shows the TM
voltage over the temperature for a typical design with a
recommended 6.8kΩ NTC (P/N: NTHS0805N02N6801 from
Vishay) and 1kΩ resistor RTM1. We recommend using those
resistors for the accurate temperature compensation.
There are two comparators with hysteresis to compare the
TM pin voltage to the fixed thresholds for VR_FAN and
VR_HOT signals respectively. The VR_FAN signal is set to
high when the TM voltage is lower than 39.1% of VCC
voltage, and is pulled to GND when the TM voltage
increases to above 45.1% of VCC voltage. The VR_FAN
signal is set to high when the TM voltage goes below 33.3%
of VCC voltage, and is pulled to GND when the TM voltage
goes back to above 39.1% of VCC voltage. Figure 14 shows
the operation of those signals.
May 28, 2009
FN6482.1