ISL6442IA Intersil, ISL6442IA Datasheet - Page 12

• Manufacturer Part Number: ISL6442IA
• Description: IC PWM BUCK VM 24QSOP
• Manufacturer: Intersil

Specifications of ISL6442IA

• Pwm Type: Voltage Mode
• Number Of Outputs: 3
• Frequency - Max: 2.85MHz
• Duty Cycle: 100%
• Voltage - Supply: 4.5 V ~ 24 V
• Buck: Yes
• Boost: No
• Flyback: No
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: No
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 24-QSOP
• Frequency-max: 2.85MHz
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

High frequency decoupling capacitors should be placed as
close to the power pins of the load as physically possible. Be
careful not to add inductance in the circuit board wiring that
could cancel the usefulness of these low inductance
components. Consult with the manufacturer of the load on
specific decoupling requirements. Keep in mind that not all
applications have the same requirements; some may need
many ceramic capacitors in parallel; others may need only one.
Use only specialized low-ESR capacitors intended for
switching-regulator applications for the bulk capacitors. The
bulk capacitor’s ESR will determine the output ripple voltage
and the initial voltage drop after a high slew-rate transient.
An aluminum electrolytic capacitor's ESR value is related to
the case size with lower ESR available in larger case sizes.
However, the equivalent series inductance (ESL) of these
capacitors increases with case size and can reduce the
usefulness of the capacitor to high slew-rate transient loading.
Unfortunately, ESL is not a specified parameter. Work with
your capacitor supplier and measure the capacitor’s
impedance with frequency to select a suitable component. In
most cases, multiple electrolytic capacitors of small case size
perform better than a single large case capacitor.
INPUT CAPACITOR SELECTION
Use a mix of input bypass capacitors to control the voltage
overshoot across the MOSFETs. Use small ceramic
capacitors for high frequency decoupling and bulk capacitors
to supply the current needed each time Q1 (upper FET)
turns on. Place the small ceramic capacitors physically close
to the MOSFETs and between the drain of Q1 and the source
of Q2 (lower FET).
The important parameters for the bulk input capacitor are the
voltage rating and the RMS current rating. For reliable
operation, select the bulk capacitor with voltage and current
ratings above the maximum input voltage and largest RMS
current required by the circuit. The capacitor voltage rating
should be at least 1.25 times greater than the maximum
input voltage and a voltage rating of 1.5 times is a
conservative guideline. The RMS current rating requirement
for the input capacitor of a buck regulator is approximately
1/2 the DC load current.
SWITCHER MOSFET SELECTION
V
allowed, so both FETs should have a source-drain
breakdown voltage (V
voltage expected; 20V or 30V are typical values available.
The ISL6442 gate drivers (UGATE
designed to drive single FETs (for up to ~10A of load current) or
smaller dual FETs (up to 4A). Both sets of drivers are sourced
by the internal VCC regulator (unless V
case the gate driver current comes from the external 5V
supply). The maximum current of the regulator (I
listed in the “Electrical Specifications” Table on page 4; this may
limit how big the FETs can be. In addition, the power dissipation
IN
for the ISL6442 has a wide operating voltage range
DS
) above the maximum supply
12
x
and LGATE
IN
= V
CC
x
CC_max)
= 5V, in which
) were
is
ISL6442
of the regulator is a major contributor to the overall IC power
dissipation (especially as C
increases).
Since V
ways. First, the FET gate-source voltage rating (V
as low as 12V (this rating is usually consistent with the 20V
or 30V breakdown chosen above). Second, the FETs must
have a low threshold voltage (around 1V), in order to have its
r
that is typically used for these applications. While some
FETs are also rated with gate voltages as low as 2.7V, with
typical thresholds under 1V, these can cause application
problems. As LGATE shuts off the lower FET, it does not
take much ringing in the LGATE signal to turn the lower FET
back on, while the Upper FET is starting to turn on, causing
some shoot-through current. Therefore, avoid FETs with
thresholds below 1V.
If the power efficiency of the system is important, then other
FET parameters are also considered. Efficiency is a
measure of power losses from input to output, and it
contains two major components: losses in the IC (mostly in
the gate drivers) and losses in the FETs. For low duty cycle
applications (such as 12V in to 1.5V out), the upper FET is
usually chosen for low gate charge, since switching losses
are key, while the lower FET is chosen for low r
it is on most of the time. For high duty cycles (such as 5.0V
in to 3.3V out), the opposite may be true.
Feedback Compensation Equations
This section highlights the design consideration for a voltage
mode controller requiring external compensation. To address a
broad range of applications, a type-3 feedback network is
recommended (see Figure 13).
Figure 14 highlights the voltage-mode control loop for a
synchronous-rectified buck converter, applicable to the
ISL6442 circuit. The output voltage (V
reference voltage, V
voltage) is compared with the oscillator (OSC) modified
sawtooth wave to provide a pulse-width modulated wave with
an amplitude of V
smoothed by the output filter (L and C). The output filter
capacitor bank’s equivalent series resistance is represented by
the series resistor E.
DS(ON)
FIGURE 13. COMPENSATION CONFIGURATION FOR ISL6442
CC
rating at V
R1
is around 5V, that affects the FET selection in two
CIRCUIT
R2
IN
GS
REF
at the PHASE node. The PWM wave is
C2
R3
= 4.5V in the 10mΩ to 40mΩ range
C3
C1
. The error amplifier output (COMP pin
in
of the FET or V
COMP
FB
OUT
V
OUT
) is regulated to the
ISL6442
IN
or F
DS(ON)
October 31, 2008
SW
GS
) can be
, since
FN9204.2