L5991D STMicroelectronics, L5991D Datasheet - Page 13

• Manufacturer Part Number: L5991D
• Description: IC PRIMARY CTRLR W/STANDBY SO16
• Manufacturer: STMicroelectronics

Specifications of L5991D

• Mfg Application Notes: 25W Off-Line Battery Charger with L5991A AppNote 300W Forward Converter with L5991A AppNote 45W AC-DC Adapter with Standby AppNote 60W Power Supply using the L5991 AppNote 80W Adapter using L6561/L5991A AppNote 90W SMPS for Monitors with Standby AppNote Trick Enhances L5991s Standby Function AppNote L5991-Based Converter, Temp Extra Power AppNote Auxiliary Power Supply Design AppNote Minimize Power Losses AppNote
• Pwm Type: Current Mode
• Number Of Outputs: 1
• Frequency - Max: 1MHz
• Duty Cycle: 93%
• Voltage - Supply: 11 V ~ 20 V
• Buck: No
• Boost: Yes
• Flyback: Yes
• Inverting: No
• Doubler: No
• Divider: No
• Cuk: No
• Isolated: Yes
• Operating Temperature: 0°C ~ 105°C
• Package / Case: 16-SOIC (3.9mm Width)
• Frequency-max: 1MHz
• Duty Cycle (max): 93 %
• Output Voltage: 5.075 V
• Output Current: 1500 mA
• Mounting Style: SMD/SMT
• Switching Frequency: 1000 KHz
• Operating Supply Voltage: 12 V to 20 V
• Maximum Operating Temperature: + 150 C
• Fall Time: 35 ns
• Minimum Operating Temperature: - 40 C
• Rise Time: 70 ns
• Synchronous Pin: Yes
• Topology: Boost, Flyback
• Number Of Pwm Outputs: 1
• On/off Pin: No
• Adjustable Output: No
• Switching Freq: 1MHz
• Operating Supply Voltage (max): 20V
• Operating Temperature Classification: Automotive
• Mounting: Surface Mount
• Pin Count: 16
• Package Type: SO
• For Use With: 497-8226 - BOARD EVAL L5991/STP12NK80Z497-6416 - BOARD EVAL L5991/STP10NK60Z497-5083 - EVAL BOARD 3PH PWR SUPPLY W/ESBT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

Figure 30. Disable (Latched).
connecting DC-LIM to VREF (half duty cycle op-
tion), Dx will be set approximately at:
Figure 31. Half duty cycle option.
Figure 32. Standby function internal schematic and operation.
DISABLE
SIGNAL
C
FB
DIS
5
2.5
D
x
+
-
14
2.5V
2 R
COMP
6
V15=GND
V5=V13=GND
V15=VREF
V5=V13=GND
+
-
R
T
2.5/4
T
260
STANDBY BLOCK
t c
t c
+
-
2R
R
13
11
ISEN
UVLO
LEVEL SHIFT
D
R
+
-
10V
Q
DISABLE
STANDBY
D97IN502
t
d
t
d
R
DRIVER
and the output switching frequency will be halved
with respect to the oscillator one because an in-
ternal T flip-flop (see block diagram) is activated.
Fig. 31 shows the operation.
The half duty cycle option speeds up the dis-
charge of the timing capacitor C
duty cycles as close to 50% as possible) so the
oscillator frequency - with the same timing compo-
nents will be slightly higher.
Pin 16. S-BY (Standby Function). The resistor R
along with R
oscillator in normal operation (f
as the STANDBY signal is high, the pin is inter-
nally connected to the reference voltage VREF by
a N-channel FET (see fig. 32), so the timing ca-
pacitor C
the STANDBY signal goes low the N-channel FET
is turned off and the pin becomes floating. R
D97IN498
16
4
2
OUT
VREF
ST-BY
RCT
R
B
T
is charged through R
V10
V10
V2
V2
A
R
C
A
, sets the operating frequency of the
T
STANDBY
HIGH
LOW
D
D
X
X
D97IN752B
=
=
2 ·t c + t d
t c + t d
t c
t c
2.5V
V
T1
osc
L5991 - L5991A
V
4V
T2
T
A
). In fact, as long
(in order to get
and R
V
COMP
B
. When
13/23
B
B
is
,