DS18B20U+T&R Maxim Integrated Products, DS18B20U+T&R Datasheet - Page 12

• Manufacturer Part Number: DS18B20U+T&R
• Description: IC THERM MICROLAN PROG-RES 8USOP
• Manufacturer: Maxim Integrated Products

Specifications of DS18B20U+T&R

• Function: Thermometer, Thermostat
• Topology: Register Bank, Scratchpad
• Sensor Type: Internal
• Sensing Temperature: -55°C ~ 125°C
• Output Type: 1-Wire®
• Output Alarm: Yes
• Output Fan: No
• Voltage - Supply: 3 V ~ 5.5 V
• Operating Temperature: -55°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
• Full Temp Accuracy: +/- 2 C
• Digital Output - Bus Interface: Serial (1-Wire)
• Digital Output - Number Of Bits: 12 bit
• Maximum Operating Temperature: + 125 C
• Minimum Operating Temperature: - 55 C
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

COPY SCRATCHPAD [48h]
This command copies the contents of the scratchpad T
to EEPROM. If the device is being used in parasite power mode, within 10µs (max) after this command is
issued the master must enable a strong pullup on the 1-Wire bus for at least 10ms as described in the
Powering the DS18B20 section.
RECALL E
This command recalls the alarm trigger values (T
places the data in bytes 2, 3, and 4, respectively, in the scratchpad memory. The master device can issue
read time slots following the Recall E
transmitting 0 while the recall is in progress and 1 when the recall is done. The recall operation happens
automatically at power-up, so valid data is available in the scratchpad as soon as power is applied to the
device.
READ POWER SUPPLY [B4h]
The master device issues this command followed by a read time slot to determine if any DS18B20s on the
bus are using parasite power. During the read time slot, parasite powered DS18B20s will pull the bus
low, and externally powered DS18B20s will let the bus remain high. See the Powering the DS18B20
section for usage information for this command.
Table 3. DS18B20 Function Command Set
Note 1:
Note 2:
Note 3:
Convert T
Read
Scratchpad
Write
Scratchpad
Copy
Scratchpad
Recall E
Read Power
Supply
COMMAND
2
For parasite-powered DS18B20s, the master must enable a strong pullup on the 1-Wire bus during temperature
conversions and copies from the scratchpad to EEPROM. No other bus activity may take place during this time.
The master can interrupt the transmission of data at any time by issuing a reset.
All three bytes must be written before a reset is issued.
2
[B8h]
Initiates temperature
conversion.
Reads the entire scratchpad
including the CRC byte.
Writes data into scratchpad
bytes 2, 3, and 4 (T
and configuration
registers).
Copies T
configuration register data
from the scratchpad to
EEPROM.
Recalls T
configuration register data
from EEPROM to the
scratchpad.
Signals DS18B20 power
supply mode to the master.
DESCRIPTION
H
H
TEMPERATURE CONVERSION COMMANDS
, T
, T
L
L
, and
, and
H
2
, T
command and the DS18B20 will indicate the status of the recall by
MEMORY COMMANDS
L
,
PROTOCOL
12 of 22
H
BEh
4Eh
B8h
B4h
44h
48h
and T
H
, T
L
L
) and configuration data from EEPROM and
and configuration registers (bytes 2, 3 and 4)
DS18B20 transmits
conversion status to master
(not applicable for parasite-
powered DS18B20s).
DS18B20 transmits up to 9
data bytes to master.
Master transmits 3 data bytes
to DS18B20.
None
DS18B20 transmits recall
status to master.
DS18B20 transmits supply
status to master.
COMMAND IS ISSUED
ACTIVITYAFTER
1-Wire BUS
NOTES
DS18B20
1
2
3
1