TDA3681ATH/N1C,518 NXP Semiconductors, TDA3681ATH/N1C,518 Datasheet - Page 2
![no-image](/images/manufacturer_photos/0/4/487/nxp_semiconductors_sml.jpg)
TDA3681ATH/N1C,518
Manufacturer Part Number
TDA3681ATH/N1C,518
Description
IC VOLT REG W/SW & IGNIT 20-HSOP
Manufacturer
NXP Semiconductors
Datasheet
1.TDA3681ATHN1S518.pdf
(22 pages)
Specifications of TDA3681ATH/N1C,518
Applications
Ignition Buffer, Regulator
Current - Supply
110µA
Voltage - Supply
9.5 V ~ 18 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
20-HSOP
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
935285812518
TDA3681ATH/N1C-T
TDA3681ATH/N1C-T
TDA3681ATH/N1C-T
TDA3681ATH/N1C-T
Philips Semiconductors
FEATURES
General
Protections
ORDERING INFORMATION
2003 Aug 29
TDA3681ATH
Extremely low noise behaviour and good stability with
very small output capacitors
Second supply pin for regulators 3 and 4 to reduce
power dissipation (e.g. via a DC-to-DC converter)
Three V
and 4) and a power switch
Regulator 2, reset and ignition buffer operational during
load dump and thermal shutdown
Combined control pin for switching regulators 1 and 3
Separate control pins for switching regulator 4 and the
power switch
Supply voltage range from 18 V to +50 V
Low quiescent current in standby mode (when
regulators 1, 3 and 4 and power switch are switched off
and ignition input is low)
Hold output for low V
protection
Reset (push-pull output stage) for regulator 2 and hold
output (open-collector output)
Adjustable reset delay time
High supply voltage ripple rejection
Backup capacitor for regulator 2
One independent ignition buffer (active HIGH).
Reverse polarity safe (down to 18 V without high
reverse current)
Able to withstand voltages up to 18 V at the outputs
(supply line may be short-circuited)
ESD protection on all pins
Thermal protections
Load dump protection
Multiple voltage regulator with
switch and ignition buffer
NUMBER
TYPE
P
-state controlled regulators (regulators 1, 3
HSOP20
NAME
P
, load dump and temperature
plastic, heatsink small outline package; 20 leads; low stand-off height
2
DESCRIPTION
GENERAL DESCRIPTION
The TDA3681A is a multiple output voltage regulator with
a power switch and an ignition buffer. It is intended for use
in car radios with or without a microcontroller.
The TDA3681A contains the following:
PACKAGE
Foldback current limit protection for regulators 1, 2, 3
and 4
Delayed second current limit protection for the power
switch (at short circuit)
The regulator outputs and the power switch are
DC short-circuit safe to ground and supply (V
Four fixed voltage regulators with a foldback current
protection (regulators 1, 2, 3 and 4). Regulator 2, which
is intended to supply a microcontroller, also operates
during load dump and thermal shutdown
Regulators 3 and 4 have a second supply pin that can
be connected to a lower supply voltage (> 6.5 V) to
reduce the power dissipation
A power switch with protection, operated by a control
input
Reset and hold outputs that can be used to interface
with the microcontroller; the reset signal can be used to
call up the microcontroller
Both supply pins can withstand load dump pulses and
negative supply voltages
Regulator 2, which is in regulation at a backup voltage
above 6.5 V
A provision for the use of a reserve supply capacitor that
will hold enough energy for regulator 2 (5 V continuous)
to allow a microcontroller to prepare for loss of voltage
An ignition input Schmitt trigger with push-pull output
stage.
Product specification
TDA3681A
VERSION
SOT418-3
P
).