TLE6281G Infineon Technologies, TLE6281G Datasheet - Page 9

• Manufacturer Part Number: TLE6281G
• Description: IC H-BRIDGE DRIVER PDSO-20
• Manufacturer: Infineon Technologies
• Type: Brush Type DC Motor Driverr

Specifications of TLE6281G

• Applications: DC Motor Driver, H Bridge
• Number Of Outputs: 1
• Voltage - Supply: 7.5 V ~ 60 V
• Operating Temperature: -40°C ~ 150°C
• Mounting Type: Surface Mount
• Package / Case: DSO-20
• Supply Current: 15 mA
• Mounting Style: SMD/SMT
• Packages: PG-DSO-20
• Operating Range: 7.5 - 60.0 V
• Iq: 0.6 mA
• Turn On/off Current: 0.85 / 0.85 A
• D.c.-range: 0...96/ 100%
• Numbers Of Integrated Opamps For Load Current Measurement: 0.0
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Current - Output: -
• Voltage - Load: -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant
• Other names: SP000107818; SP000362093; TLE6281G; TLE6281GNT; TLE6281GT; TLE6281GTR

output stage the ER1 is pulled down. This shut down can be caused by undervoltage or
short circuit. In this condition ER2 indicates the reason for the shut down.
Condition of
ER1 pin
5V
5V
0V
0V
Recommended Start-up procedure
The following procedure is recommended whenever the Driver IC is powered up:
Shut down of the driver
A shut down can be caused by undervoltage or short circuit. A short circuit will shut down
only the affected Mosfet until a reset of the error register by a disable of the driver occurs. A
shut down due to short circuit will occur only when the Short Circuit criteria V
a duration equal to or longer than the Short Circuit filter time t
above V
shorter than t
An undervoltage shut down shuts only the affected output down. The affected output will
auto restart after the undervoltage situation is over.
Operation at Vs<12V
If Vs<11.5V the gate voltage will not reach 10V. It will reach approx Vs-1.5V, dependent on
duty cyle, bootstrap capacitor, total gate charge of the external Mosfet and switching fre-
quency.
Operation at different voltages for Vs, DH1 and DH2
If DH1 and DH2 are used with a voltage higher than Vs, a duty cycle of 100% can not be
guaranteed. In this case the driver is acting like a normal driver IC based on the bootstrap
principle. This means that after a maximum “On” time of the highside switch of more than
1ms a refresh pulse to charge the bootstrap capacitor of about 1µs is needed to avoid un-
dervoltage lock out of this output stage.
Operation at extreme duty cycle:
The integrated charge pump allows an operation at 100% duty cycle. The charge pump is
strong enough to replace leakage currents during “on”-phase of the highside switch. The
gate charge for fast switching of the highside switches is supplied by the bootstrap capaci-
Data Sheet
• Disable the Driver IC via DT/DIS pin
• Wait until the bootstrap capacitors C
• Enable the Driver IC via DT/DIS pin
• Start the operation by applying the desired pulse patterns. Do not apply any pulse pat-
application conditions, e.g. C
terns to the PWM or DIR pin, before the C
DS(SCP)
scp(off)
is not counted or accumulated. Hence, repetitive Short Circuit conditions
Condition of
ER2 pin
5V
0V
5V
0V
will not result in a shut down of the affected MOSFET.
Function
no errors
overtemperature warning of driver IC
Shut down of any output stage caused by short circuit
Shut down of any output stage caused by undervoltage
Bx
and R
Bx
Bx
9
are charged (the waiting time depends on
)
Bx
capacitors are charged up.
SCP(off)
Data Sheet TLE 6281G
. Yet, the exposure to or
Rev 2.3 2007-01-11
DS(SCP)
is met for