MC33291DW Freescale Semiconductor, MC33291DW Datasheet - Page 13

• Manufacturer Part Number: MC33291DW
• Description: IC SWITCH 8X L-SIDE W/SPI 24SOIC
• Manufacturer: Freescale Semiconductor
• Type: Low Sider

Specifications of MC33291DW

• Input Type: SPI
• Number Of Outputs: 8
• On-state Resistance: 600 mOhm
• Current - Output / Channel: 500mA
• Current - Peak Output: 3A
• Voltage - Supply: 9 V ~ 26.5 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• For Use With: KIT33291DWEVB - KIT EVAL FOR MC33291 SMART SW
• Lead Free Status / RoHS Status: Contains lead / RoHS non-compliant

input fashion using SPI, illustrated in
shows a possible 24 loads being controlled by only three
dedicated parallel MCU ports used for chip select.
controlling multiple 33291 devices using two MCUs. A system
can have only one master MCU at any given instant of time
and one or more slave MCUs. Master control of the system
must pass from one MCU to the other in an orderly manner.
The master MCU supplies the system clock signal (top MCU
designated the master); the lower MCU being the slave. It is
possible to have a system with more than one master;
Analog Integrated Circuit Device Data
Freescale Semiconductor
Microcontroller
Multiple 33291 devices can also be controlled in a parallel
Figure
Parallel
Ports
MC68XX
SPI
16, page 14, illustrates a basic method of
Microcontroller
A0
A1
A2
Figure 15. Parallel Input SPI Control
MC68XX
SPI
MOSI
SCLK
SCLK
Parallel Port
MISO
IRQ
MOSI
Figure
CS
SO
8 Outputs
SI
SCLK
CS
SI
SCLK
CS
SI
SCLK
CS
33291
Figure 14. 33291 SPI System Daisy Chain
33291
33291
33291
15. This figure
SCLK
SI
8 Outputs
8 Outputs
8 Outputs
CS
SO
8 Outputs
33291
however, not at the same time. Only when the master is not
communicating can a slave assume the mastership and
communicate. MCU master control is switched through the
use of the slave select (
become a slave when it detects a logic low state on its
applications where a large number of loads require efficient
control. To this end, the popular Synchronous Serial
Peripheral Interface (SPI) protocol is incorporated to
communicate efficiently with the MCU.
SPI SYSTEM ATTRIBUTES
with numerous standard peripherals and MCUs available
from Motorola and other semiconductor manufacturers. SPI
reduces the number of pins necessary for input/output (I/O)
on the 33291. It also offers an easy means of expanding the
I/O function using few MCU pins. The SPI system of
communication consists of the MCU transmitting, in return it
receives one data-bit of information per system clock cycle.
one pin, Master Out Serial In (MOSI), and received by
another pin, Master In Serial Out (MISO), of the MCU.
• Full duplex, three-wire synchronous data transfer
• Each microcontroller can be a master or a slave
• Provides write collision flag protection
• Provides end of message interrupt flag
• Four I/Os associated with SPI (MOSI, MISO, SCLK, SS)
• Drawbacks to SPI are as follows:
• An MCU is required for efficient operational control
• In contrast to parallel input control it is slower at performing
SCLK
These basic examples make the 33291 very attractive for
The SPI system is flexible enough to communicate directly
Data bits of information are simultaneously transmitted by
Some features of SPI are as follows:
pulse width modulating (PWM) functions.
SI
CS
SO
8 Outputs
33291
SCLK
SS
SI
) pin of the MCUs. A master will
FUNCTIONAL DESCRIPTION
CS
SO
8 Outputs
33291
SCLK
INTRODUCTION
SI
SS
33291
pin.
13