E-L6207D STMicroelectronics, E-L6207D Datasheet - Page 9

• Manufacturer Part Number: E-L6207D
• Description: IC DRVR FULL BRIDGE DUAL 24-SOIC
• Manufacturer: STMicroelectronics
• Type: H Bridger

Specifications of E-L6207D

• Input Type: Non-Inverting
• Number Of Outputs: 4
• On-state Resistance: 300 mOhm
• Current - Output / Channel: 2.8A
• Current - Peak Output: 5.6A
• Voltage - Supply: 8 V ~ 52 V
• Operating Temperature: -25°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 24-SOIC (7.5mm Width)
• Operating Current: 10mA
• Operating Temperature Classification: Automotive
• Package Type: SO
• Operating Supply Voltage (min): 8V
• Operating Supply Voltage (typ): 48V
• Operating Supply Voltage (max): 52V
• Operating Supply Voltage: 6.5 V
• Supply Current: 50 mA
• Mounting Style: SMD/SMT
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-4571-5

TRUTH TABLE
X
High Z
GND (Vs)
(*) Valid only in case of load connected between OUT1 and OUT2
PWM CURRENT CONTROL
The L6207 includes a constant off time PWM current controller for each of the two bridges. The current control
circuit senses the bridge current by sensing the voltage drop across an external sense resistor connected be-
tween the source of the two lower power MOS transistors and ground, as shown in Figure 7. As the current in
the load builds up the voltage across the sense resistor increases proportionally. When the voltage drop across
the sense resistor becomes greater than the voltage at the reference input (VREF
parator triggers the monostable switching the low-side MOS off. The low-side MOS remain off for the time set
by the monostable and the motor current recirculates in the upper path. When the monostable times out the
bridge will again turn on. Since the internal dead time, used to prevent cross conduction in the bridge, delays
the turn on of the power MOS, the effective off time is the sum of the monostable time plus the dead time.
Figure 7. PWM Current Controller Simplified Schematic
Figure 8 shows the typical operating waveforms of the output current, the voltage drop across the sensing re-
sistor, the RC pin voltage and the status of the bridge. Immediately after the low-side Power MOS turns on, a
high peak current flows through the sensing resistor due to the reverse recovery of the freewheeling diodes. The
L6207 provides a 1 s Blanking Time t
prematurely re-trigger the monostable.
EN
H
H
H
H
L
5V
C
5mA
= Don't care
= High Impedance Output
= GND during Ton, Vs during Toff
(0)
INPUTS
TO GATE LOGIC
IN1
X
H
H
RC A(or B)
R
L
L
(1)
2.5V
Q
+
-
IN2
S
R
X
H
H
L
L
MONOSTABLE
BLANKING TIME
MONOSTABLE
RESET
BLANK
GND (Vs)
High Z
OUT1
GND
Vs
Vs
COMPARATOR
that inhibits the comparator output so that this current spike cannot
OUTPUT
BLANKER
1 s
COMPARATOR
OUTPUTS
SENSE
DEAD TIME
DRIVERS
+
-
+
GND (Vs)
VREF A(or B)
High Z
GATE DRIVERS
OUT2
GND
FROM THE
LOW-SIDE
Vs
Vs
2H
2L
R SENSE
DEAD TIME
VS
DRIVERS
Disable
Brake Mode (Lower Path)
Forward
Reverse
Brake Mode (Upper Path)
A
+
(or B)
SENSE A(or B)
A
1H
1L
or VREF
Description (*)
OUT2 A(or B)
OUT1 A(or B)
D02IN1352
I OUT
B
) the sense com-
LOAD
(or
B
)
A
L6207
9/23