ITS711L1 Infineon Technologies, ITS711L1 Datasheet
ITS711L1
Specifications of ITS711L1
Available stocks
Related parts for ITS711L1
ITS711L1 Summary of contents
Page 1
... Operating voltage Operating temperature active channels: On-state resistance R Nominal load current I Current limitation protection technology. Providing embedded protective functions. =150 ) in GND connection, resistor in series with ST GND 1 PROFET ® ITS711L1 V bb(AZ) V 5.0 ... 34 bb(on) T -30 … +85 a one two parallel four parallel 200 ...
Page 2
... Short to Vbb detection 1 Charge Gate 2 Current pump 2 protection limit 2 Level shifter Limit for unclamped Rectifier 2 ind. loads 2 Open load Short to Vbb detection 2 (equivalent to chip 1) 2 PROFET ® ITS711L1 + V bb Leadframe Channel 1 18 OUT1 Temperature sensor 1 Channel 2 17 OUT2 Temperature sensor GND1/2 ...
Page 3
... GND and status pins, e.g. with a bb(AZ) resistor in series with the status pin. A resistor for input 2 (one layer thick) copper area for PROFET ® ITS711L1 Symbol Values ...
Page 4
... =-40...+25° =+150° =-40...+150° =-40...+150° =-40...+150° =-40...+150° =-40...+150° 5.6 V typ without charge pump PROFET ® ITS711L1 Values min typ -- 165 ON 320 83 42 1.7 1.9 2.6 2.8 4.1 4 200 80 200 0 0.1 -- off 5.0 ...
Page 5
... I L(SCr) two parallel channels four parallel channels T =-40°C: t j,start off(SC 25°C: j,start V 11 > out bb 5 PROFET ® ITS711L1 Values min typ -- 5.5 9.5 4.5 7.5 2.5 4.5 twice the current of one channel four times the current of one channel -- 4 ...
Page 6
... =-40..+150° =-40..+150° =-40..+150° +1.6 mA +1.6 mA +1.6 mA PROFET ® ITS711L1 Symbol Values min typ (OL twice the current of one channel four times the current of one channel 2 3 OUT(OL 2.5 3.5 I 1.7 -- IN(T+) 1.5 -- IN(T 0.5 IN(T) ...
Page 7
... Z = high impedance, potential depends on external circuit V ON1 Leadframe V ON2 OUT1 I L2 Chip 1 17 OUT2 V IN3 V IN4 V ST3/4 V OUT1 2 V OUT2 I GND1 150 GND1/2 GND3/4 in the off state causes an internal current from output to ground PROFET ® ITS711L1 OUT1 OUT2 ST1/2 OUT3 OUT4 ST3/4 BTS 711L1 H ...
Page 8
... V typ. ON ON(CL) Infineon Technologies AG IN1...4 Overvoltage protection of logic part GND1/2 or GND3 +5V R GND ST Reverse battery protection ESD GND +V bb Temperature protection is not active during inverse current operation OUT 8 PROFET ® ITS711L1 Logic GND Signal GND = 6.1 V typ typ 3 150 ± Logic ...
Page 9
... Consider at your PCB layout that in the case of Vbb dis- connection with energized inductive load the whole load current flows through the GND connection. OUT1 OUT2 OUT IN IN(T+) 9 PROFET ® ITS711L1 V bb IN1 V OUT1 IN1 PROFET IN2 V OUT2 IN2 ST ...
Page 10
... OUT L { 350 300 250 L 200 150 100 i (t) dt, · ON(CL · ( OUT(CL) Typ. open load detection current I L(OL L(OL) 140 120 100 2 [A] 10 PROFET ® ITS711L1 = 1 high 150°C 85°C 25°C -40° high [mA] -40°C 25°C 85° 2006-Mar- [ 150° [V] bb ...
Page 11
... Typ. standby current ); V = 9... 1...4 = low bb(off bb(off - Typ. initial short circuit shutdown time j,start ); V = off(SC) t [msec] off(SC - 100 Infineon Technologies AG 100 150 200 T [°C] j 150 200 T [°C] j,start 11 PROFET ® ITS711L1 2006-Mar-23 ...
Page 12
... OUT2 ST open drain Figure 2a: Switching a lamp OUT I L The initial peak current should be limited by the lamp and not by the initial short circuit current I = 7.5 A typ. of the device. L(SCp) Infineon Technologies AG PROFET ® ITS711L1 Figure 2b: Switching an inductive load IN t d(ST OUT L(OL) t ...
Page 13
... IN1 IN2 channel 2: normal operation V OUT1 I L1 channel 1: open load t d(ST The status delay time t failure modes "open load in ON-state" and "overtemperature". 13 PROFET ® ITS711L1 open normal load load d(ST OL1) d(ST OL2) d(ST OL2 typ d(ST OL2 ...
Page 14
... Figure 6b: Undervoltage restart of charge pump bb(under) d(ST OL5) d(ST high, normal load conditions. Charge pump starts at V Figure 7a: Overvoltage bb(u cp) V bb(u rst) V OUT PROFET ® ITS711L1 V ON(CL) V bb(over bb(o rst) bb(u rst) V bb(u cp) = 5.6 V typ. bb(ucp bb(over) ON(CL) 2006-Mar- bb(o rst) t ...
Page 15
... Pin 15 Printed circuit board (FR4, 1.5mm thick, one layer 70 m, 6cm power dissipation P , nominal load current I tot Infineon Technologies AG Ordering Code SP000219532 : s 2 active heatsink area reference for max. and thermal resistance R L(NOM) 15 PROFET ® ITS711L1 thja 2006-Mar-23 ...
Page 16
... Life support devices or systems are intended to be implanted in the human body support and/or maintain and sustain and/or protect human life. If they fail reasonable to assume that the health of the user or other persons may be endangered. Infineon Technologies AG PROFET ® ITS711L1 16 2006-Mar-23 ...