L6207N STMicroelectronics, L6207N Datasheet - Page 17

• Manufacturer Part Number: L6207N
• Description: IC DRVR FULL BRDG DUAL 24-PWRDIP
• Manufacturer: STMicroelectronics
• Type: H Bridger

Specifications of L6207N

• Input Type: Non-Inverting
• Number Of Outputs: 4
• On-state Resistance: 300 mOhm
• Current - Output / Channel: 2.8A
• Current - Peak Output: 5.6A
• Voltage - Supply: 8 V ~ 52 V
• Operating Temperature: -25°C ~ 125°C
• Mounting Type: Through Hole
• Package / Case: 24-DIP (0.300", 7.62mm)
• Operating Supply Voltage: 8 V to 52 V
• Supply Current: 0.01 A
• Mounting Style: Through Hole
• For Use With: 497-4934 - BOARD MOTOR STEPPER/DC L6207 DIP
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-3645

OUTPUT CURRENT CAPABILITY AND IC POWER DISSIPATION
In Fig. 17 and Fig. 18 are shown the approximate relation between the output current and the IC power dissipa-
tion using PWM current control driving two loads, for two different driving types:
– One Full Bridge ON at a time (Fig.17) in which only one load at a time is energized.
– Two Full Bridges ON at the same time (Fig.18) in which two loads at the same time are energized.
For a given output current and driving type the power dissipated by the IC can be easily evaluated, in order to
establish which package should be used and how large must be the on-board copper dissipating area to guar-
antee a safe operating junction temperature (125°C maximum).
Figure 17. IC Power Dissipation versus Output Current with One Full Bridge ON at a time.
Figure 18. IC Power Dissipation versus Output Current with Two Full Bridges ON at the same time.
THERMAL MANAGEMENT
In most applications the power dissipation in the IC is the main factor that sets the maximum current that can be de-
livered by the device in a safe operating condition. Therefore, it has to be taken into account very carefully. Besides
the available space on the PCB, the right package should be chosen considering the power dissipation. Heat sinking
can be achieved using copper on the PCB with proper area and thickness. Figures 20, 21 and 22 show the Junction-
to-Ambient Thermal Resistance values for the PowerSO36, PowerDIP24 and SO24 packages.
For instance, using a PowerSO package with copper slug soldered on a 1.5 mm copper thickness FR4 board
with 6cm
ing methods for this package. Using a multi-layer board with vias to a ground plane, thermal impedance can be
reduced down to 15°C/W.
2
dissipating footprint (copper thickness of 35µm), the R
P
P
D
D
TWO FULL BRIDGES ON AT THE SAME TIME
[W ]
[W]
10
10
8
6
4
2
0
8
6
4
2
0
0
0
ONE FULL BRIDGE ON AT A TIME
0.5
0.5
1
1
I
I
OUT
OUT
1.5
1.5
[A ]
[A]
2
2
2.5
2.5
3
3
I
I
I
I
A
B
A
B
th j-amb
Test Conditions:
Supply Voltage = 24V
Test Conditions:
Supply Voltage = 24V
I
OUT
I
is about 35°C/W. Fig. 19 shows mount-
OUT
No PWM
f
I
No PWM
f
SW
OUT
SW
= 3 0 kHz (slow decay)
= 30 kHz (slow decay)
I
OUT
L6207
17/23