L6743Q STMicroelectronics, L6743Q Datasheet - Page 7

• Manufacturer Part Number: L6743Q
• Description: IC MOSFET DRIVER HI CURR 10-DFN
• Manufacturer: STMicroelectronics
• Type: High Side/Low Sider

Specifications of L6743Q

• Configuration: High and Low Side, Synchronous
• Input Type: Non-Inverting
• Current - Peak: 2A
• Number Of Configurations: 1
• Number Of Outputs: 2
• Voltage - Supply: 5 V ~ 12 V
• Operating Temperature: 0°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 10-DFN
• Supply Voltage (min): 5 V
• Supply Current: 5 mA
• Maximum Power Dissipation: 2250 mW
• Maximum Operating Temperature: + 125 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: 0 C
• Number Of Drivers: 2
• Flexible Gate-drive: 5V to 12V compatible
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Delay Time: -
• High Side Voltage - Max (bootstrap): -
• Lead Free Status / Rohs Status: Lead free / RoHS Compliant

L6743, L6743Q
5
Device description and operation
L6743, L6743Q provides high-current driving control for both high-side and low-side
N-channel MOSFETS connected as step-down DC-DC Converter driven by an external
PWM signal. The integrated high-current drivers allow using different types of power
MOSFETs (also multiple MOS to reduce the equivalent R
transition.
The driver for the high-side MOSFET use BOOT pin for supply and PHASE pin for return.
The driver for the low-side MOSFET use the VCC pin for supply and PGND pin for return.
The driver embodies a anti-shoot-through and adaptive dead-time control to minimize Low-
Side body diode conduction time maintaining good efficiency saving the use of Schottky
diodes: when the high-side MOSFET turns off, the voltage on its source begins to fall; when
the voltage reaches about 2 V, the low-side MOSFET gate drive voltage is suddenly applied.
When the low-side MOSFET turns off, the voltage at LGATE pin is sensed. When it drops
below about 1 V, the high-side MOSFET gate drive voltage is suddenly applied. If the
current flowing in the inductor is negative, the source of highside MOSFET will never drop.
To allow the low-side MOSFET to turn-on even in this case, a watchdog controller is
enabled: if the source of the high-side MOSFET doesn't drop, the low-side MOSFET is
switched on so allowing the negative current of the inductor to recirculate. This mechanism
allows the system to regulate even if the current is negative.
Before VCC to overcome the UVLO threshold, L6743, L6743Q keeps firmly-OFF both high-
side and low-side MOSFETS then, after the UVLO has been crossed, the EN and PWM
inputs take the control over driver’s operations. EN pin enables the driver: if low will keep all
MOSFET OFF (HiZ) regardless of the status of PWM. When EN is high, the PWM input
takes the control: if left floating, the internal resistor divider sets the HiZ state: both
MOSFETS are kept in the OFF state until PWM transition.
After UVLO crossing and while in HiZ, the preliminary-OV protection is activated: if the
voltage senses through the PHASE pin overcomes about 1.8 V, the low-side MOSFET is
latched ON in order to protect the load from dangerous over-voltage. The driver status is
reset from a PWM transition.
Driver power supply as well as power conversion input are flexible: 5 V and 12 V can be
chosen for high-side and low-side MOSFET voltage drive.
Figure 4.
PWM
HS Gate
LS Gate
Timing diagram (EN = High)
HiZ Window
t
hold-off
Device description and operation
DS(on)
HiZ Window
), maintaining fast switching
t
hold-off
7/17