E-L6574D013TR STMicroelectronics, E-L6574D013TR Datasheet
E-L6574D013TR
Specifications of E-L6574D013TR
Related parts for E-L6574D013TR
E-L6574D013TR Summary of contents
Page 1
... An integrated bootstrap section, eliminating the nor- mally required bootstrap diode and the zener clamp- ing on Vs, makes the L6574 well suited for low cost applications where few additional components are needed to build a high performance ballast. V ...
Page 2
... Non Inverting Input of the operational amplifier. 8 EN1 Enable 1. This pin (active high), forces the device in a latched shutdown state (like in the under voltage conditions). There are two ways to resume normal operation: – the first is to reduce the supply voltage below the undervoltage threshold and then increase it again until the valid supply is recognised. – ...
Page 3
... Supply Voltage. This pin, connected to the supply filter capacitor, is internally clamped (15.6V typical). 13 N.C. Non Connected. This pin set a distance between the pins related to the HV and those related to the LV side. 14 OUT High Side Driver Floating Reference. This pin must be connected close to the source of the high side power MOS or IGBT ...
Page 4
... L6574 RECOMMENDED OPERATING CONDITIONS Symbol V Supply Voltage S V (*) High Side Reference OUT V (*) Floating Supply Voltage BOOT (*) If the condition Vboot - Vout < guaranteed, Vout can range from -3 to 580V. ELECTRICAL CHARACTERISTCS (V = 12V 12V BOOT OUT Symbol Pin Parameter Supply Voltage Turn On Threshold suvp ...
Page 5
... MOSFET. This function is achieved using a high voltage DMOS driver which is driven synchronously with the low side external power MOSFET. For a safe operation, current flow into the Vboot pin is inhibited, even though ZVS operation may not be ensured. Timing Section: To set the proper preheat time (tpre=kpre*Cpre) for the bulb, a capacitor is connected to the Cpre pin which is charged with a fixed current ...
Page 6
... Short pulses (>200nsec) at the comparator inputs are rec- ognized. The EN1 input (active high) forces the L6574 in the shut down state (e.g. LVG low, HVG low, oscillator stopped) in the event of an undervoltage condition. Normal operating condition is resumed after a power- off power-on sequence or when EN2 input is high ...
Page 7
... Figure ING ING f ING (KHz) 100 Figure with R PRE f (KHz) RING=33K Figure with R PRE f (KHz) RING=50K 100 Figure 4. f vs. R D98IN867 (KHz) 100 100 ING = 33k Figure 5. f ING f D98IN868 ING (KHz) 100 PRE = 50k Figure 6. f ING ...
Page 8
... G 4.6 5.3 0.181 L 0.4 1.27 0.016 M 0.62 8˚(max.) S (1) D and F do not include mold flash or protrusions. Mold flash or potrusions shall not exceed 0.15mm (.006inch). 8/10 inch MIN. TYP. MAX. 0.069 0.009 0.063 Weight: 0.20gr 0.018 0.010 0.020 0.394 0.244 ...
Page 9
... DIM. MIN. TYP. MAX. MIN. a1 0.51 0.020 B 0.77 1.65 0.030 b 0 8.5 e 2.54 e3 17.78 F 7.1 I 5.1 L 3.3 Z 1.27 inch MECHANICAL DATA TYP. MAX. 0.065 0.020 0.010 0.787 0.335 0.100 0.700 0.280 0.201 0.130 0.050 L6574 OUTLINE AND DIP16 9/10 ...
Page 10
... STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics. Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States ...