CAT3616HV4-GT2 ON Semiconductor, CAT3616HV4-GT2 Datasheet - Page 9

• Manufacturer Part Number: CAT3616HV4-GT2
• Description: IC LED DRVR WHITE BCKLGT 16-TQFN
• Manufacturer: ON Semiconductor
• Type: Backlight, White LEDr

Specifications of CAT3616HV4-GT2

• Topology: Linear (LDO), Switched Capacitor (Charge Pump)
• Number Of Outputs: 6
• Internal Driver: Yes
• Type - Primary: Backlight
• Type - Secondary: White LED
• Frequency: 800kHz ~ 1.3MHz
• Voltage - Supply: 3 V ~ 5.5 V
• Voltage - Output: 7V
• Mounting Type: Surface Mount
• Package / Case: 16-TFQFN Exposed Pad
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 31mA
• Internal Switch(s): Yes
• Efficiency: 91%
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 3616HV4-GT2

3. MAIN1 to MAIN4, SUB1, SUB2 pins should not be left floating. They should be connected to the LED cathode, or tied to VOUT pin if not used.
Pin Function
VIN is the supply pin for the charge pump. A small 1 mF
ceramic bypass capacitor is required between the VIN pin
and ground near the device. The operating input voltage
range is up to 5.5 V. When the input supply falls below the
undervoltage threshold (2 V), all LED channels are disabled.
EN is the enable logic input. Logic level for high and low are
set at 1.3 V and 0.4 V respectively. When EN is initially
taken high, the device becomes enabled and all LED
currents remain at 0 mA. To place the device into zero
current shutdown mode, the EN pin must be held low for
1.5 ms or more.
ENM, ENS are the active low enable/ dimming control logic
inputs for respectively main and sub LED channels. The
falling edge of the first pulse applied to ENM and ENS sets
the current for respectively the main and sub LED channels
to their full scale of 31 mA. On each consecutive falling edge
of the pulse applied to ENM and ENS, the LED current is
decreased by 1 mA step. On the 32
is set to zero. The next pulse resets the current back to the full
scale of 31 mA.
Table 5. PIN DESCRIPTIONS
Pin #
9, 10
TAB
7, 8
12
13
14
15
16
11
1
2
3
4
5
6
C1−, C1+
C2−, C2+
MAIN1
MAIN4
MAIN3
MAIN2
VOUT
Name
SUB2
SUB1
ENM
GND
ENS
TAB
VIN
EN
MAIN1 LED cathode terminal (if not used, connect to VOUT) (Note 3)
Enable main LED (MAIN1 to MAIN4) input. Active low
Enable sub LED (SUB1, SUB2) input. Active low
Device enable input. Active high.
Charge pump output connected to the LED anodes
Supply voltage.
Bucket capacitor 1 terminal
Bucket capacitor 2 terminal
Ground reference
SUB2 LED cathode terminal (if not used, connect to VOUT) (Note 3)
SUB1 LED cathode terminal (if not used, connect to VOUT) (Note 3)
MAIN4 LED cathode terminal (if not used, connect to VOUT) (Note 3)
MAIN3 LED cathode terminal (if not used, connect to VOUT) (Note 3)
MAIN2 LED cathode terminal (if not used, connect to VOUT) (Note 3)
Connect to Ground on PCB
nd
pulse, the LED current
http://onsemi.com
9
VOUT is the charge pump output that is connected to the
LED anodes. A small 1 mF ceramic bypass capacitor is
required between the VOUT pin and ground near the device.
GND is the ground reference for the charge pump. The pin
must be connected to the ground plane on the PCB.
C1+, C1− are connected to each side of the 1 mF ceramic
bucket capacitor C1.
C2+, C2− are connected to each side of the 1 mF ceramic
bucket capacitor C2.
MAIN1−4, SUB1−2 provide the internal regulated current
for each of the LED cathodes. These pins enter a high
impedance zero current state whenever the device is placed
in shutdown mode. In applications using less than six LEDs,
the unused channels should be wired directly to VOUT. This
ensures the channel is automatically disabled dissipating
less than 200 mA.
TAB is the exposed pad underneath the package. For best
thermal performance, the tab should be soldered to the PCB
and connected to the ground plane.
Function