CAT3616HV4-GT2 ON Semiconductor, CAT3616HV4-GT2 Datasheet
CAT3616HV4-GT2
Specifications of CAT3616HV4-GT2
Available stocks
Related parts for CAT3616HV4-GT2
CAT3616HV4-GT2 Summary of contents
Page 1
... ENS GND EN (Top View) MARKING DIAGRAMS G616 AXXX YMCC G616 = CAT3616HV4−T2 CDAH = CAT3616HV4−GT2 A = Assembly Location XXX = Last Three Digits of Assembly Lot Number Y = Production Year (Last Digit Production Month (1- Country of Origin (Two Digit) Note: Two digit code for country of origin: ...
Page 2
Table 1. ABSOLUTE MAXIMUM RATINGS Parameter VIN, LEDxx voltage VOUT, C1±, C2± voltage EN, ENM, ENS voltage Storage Temperature Range Junction Temperature Range Lead Temperature Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional ...
Page 3
Table 3. ELECTRICAL OPERATING CHARACTERISTICS VIN = 3 High, ambient temperature of 25°C (over recommended operating conditions unless specified otherwise) Symbol Parameter I Quiescent Current Q I Shutdown Current QSHDN I LED Current Range with 6 LEDs ...
Page 4
Figure 2. Enable LED Timing Diagram http://onsemi.com 4 ...
Page 5
V, IOUT = LEDs VIN, ENM = ENS = GND 100 90 1x Mode 15 mA per LED ...
Page 6
V, IOUT = LEDs VIN, ENM = ENS = GND 5.0 4.0 3.0 2.0 1.0 0 −1.0 1.5x Mode −2.0 −3.0 ...
Page 7
TYPICAL CHARACTERISTICS (VIN = 3.6 V, IOUT = LEDs VIN, ENM = ENS = GND Figure 15. Power Up with 6 LEDs at 15 ...
Page 8
TYPICAL CHARACTERISTICS (VIN = 3.6 V, IOUT = LEDs VIN, ENM = ENS = GND OUT Figure 21. ENM, ENS and Output Current Dimming ...
Page 9
Table 5. PIN DESCRIPTIONS Pin # Name 1 MAIN1 MAIN1 LED cathode terminal (if not used, connect to VOUT) (Note 3) 2 ENM Enable main LED (MAIN1 to MAIN4) input. Active low 3 ENS Enable sub LED (SUB1, SUB2) input. ...
Page 10
Block Diagram Figure 24. CAT3616 Functional Block Diagram Basic Operation At power−up, the CAT3616 starts operating in 1x mode where the output will be approximately equal to the input supply voltage (less any internal voltage losses). If the output voltage ...
Page 11
LED Current Setting The LED current is controlled by toggling the input signals ENM and ENS. ENM controls the four LED channels MAIN1 to MAIN4. ENS controls the two LED lines SUB1 and SUB2. ENM and ENS work the same ...
Page 12
Application Information Single Wire Dimming Application The dimming control can be achieved through a single wire interface by connecting together all three logic input signals EN, ENM and ENS as shown on Figure 25. The common enable signal is set ...
Page 13
D PIN#1 INDEX AREA TOP VIEW SYMBOL MIN NOM A 0.70 0.75 A1 0.00 0.02 A3 0.20 REF b 0.25 0.30 D 3.90 4.00 D2 2.00 −−− E 3.90 4.00 E2 2.00 −−− e 0.65 BSC L 0.45 −−− Notes: ...
Page 14
... All packages are RoHS−compliant (Lead−free, Halogen−free). 5. The standard lead finish is NiPdAu. 6. The device used in the above example is a CAT3616HV4−GT2 (TQFN, NiPdAu Plated Finish, Tape & Reel, 2,000/Reel). 7. For Matte−Tin package option, please contact your nearest ON Semiconductor Sales office. ...