PCA9634PW/S911,118 NXP Semiconductors, PCA9634PW/S911,118 Datasheet - Page 9

• Manufacturer Part Number: PCA9634PW/S911,118
• Description: IC LED DRIVER RGBA 20-TSSOP
• Manufacturer: NXP Semiconductors
• Type: RGBA LED Driverr

Specifications of PCA9634PW/S911,118

• Topology: Open Drain, PWM
• Number Of Outputs: 8
• Internal Driver: Yes
• Type - Primary: Backlight, LED Blinker
• Type - Secondary: RGBA
• Frequency: 1MHz
• Voltage - Supply: 2.3 V ~ 5.5 V
• Voltage - Output: 5.5V
• Mounting Type: Surface Mount
• Package / Case: 20-TSSOP
• Operating Temperature: -40°C ~ 85°C
• Current - Output / Channel: 25mA
• Internal Switch(s): Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Efficiency: -
• Other names: 935285522118; PCA9634PW/S911-T; PCA9634PW/S911-T

NXP Semiconductors
PCA9634_6
Product data sheet
7.2 Control register
Following the successful acknowledgement of the slave address, LED All Call address or
LED Sub Call address, the bus master will send a byte to the PCA9634, which will be
stored in the Control register.
The lowest 5 bits are used as a pointer to determine which register will be accessed
(D[4:0]). The highest 3 bits are used as Auto-Increment flag and Auto-Increment options
(AI[2:0]).
When the Auto-Increment flag is set (AI2 = 1), the five low order bits of the Control register
are automatically incremented after a read or write. This allows the user to program the
registers sequentially. Four different types of Auto-Increment are possible, depending on
AI1 and AI0 values.
Table 3.
Remark: Other combinations not shown in
reserved and must not be used for proper device operation.
AI[2:0] = 000 is used when the same register must be accessed several times during a
single I
is overwritten each time the register is accessed during a write operation.
AI[2:0] = 100 is used when all the registers must be sequentially accessed, for example,
power-up programming.
AI[2:0] = 101 is used when the four LED drivers must be individually programmed with
different values during the same I
setting to another color setting.
AI2
0
1
1
1
1
Fig 7.
2
AI1
0
0
0
1
1
C-bus communication, for example, changes the brightness of a single LED. Data
reset state = 80h
Remark: The Control register does not apply to the Software Reset I
Control register
Auto-Increment options
AI0
0
0
1
0
1
Rev. 06 — 12 September 2008
Function
no Auto-Increment
Auto-Increment for all registers. D[4:0] roll over to ‘0 0000’ after the last
register (1 0001) is accessed.
Auto-Increment for individual brightness registers only. D[4:0] roll over to
‘0 0010’ after the last register (0 1001) is accessed.
Auto-Increment for global control registers only. D[4:0] roll over to
‘0 1010’ after the last register (0 1011) is accessed.
Auto-Increment for individual and global control registers only. D[4:0] roll
over to ‘0 0010’ after the last register (0 1011) is accessed.
AI2 AI1 AI0 D4
Auto-Increment flag
2
Auto-Increment options
C-bus communication, for example, changing color
Table 3
register address
D3
D2
(AI[2:0] = 001, 010, and 011) are
D1
002aac140
D0
8-bit Fm+ I
2
C-bus address.
PCA9634
2
© NXP B.V. 2008. All rights reserved.
C-bus LED driver
9 of 38