LM3401MM/NOPB National Semiconductor, LM3401MM/NOPB Datasheet - Page 10
![IC LED DRIVER HIGH BRIGHT 8-MSOP](/photos/6/57/65756/pkg_mua08a_sml.jpg)
LM3401MM/NOPB
Manufacturer Part Number
LM3401MM/NOPB
Description
IC LED DRIVER HIGH BRIGHT 8-MSOP
Manufacturer
National Semiconductor
Series
PowerWise®r
Type
HBLED Driverr
Datasheet
1.LM3401MMNOPB.pdf
(18 pages)
Specifications of LM3401MM/NOPB
Constant Current
Yes
Topology
PWM, Step-Down (Buck)
Number Of Outputs
1
Internal Driver
No
Type - Primary
General Purpose
Type - Secondary
High Brightness LED (HBLED)
Frequency
1.5MHz
Voltage - Supply
4.5 V ~ 35 V
Mounting Type
Surface Mount
Package / Case
8-MSOP, Micro8™, 8-uMAX, 8-uSOP,
Operating Temperature
-40°C ~ 125°C
Current - Output / Channel
1A
Internal Switch(s)
Yes
Efficiency
92%
Operating Supply Voltage (typ)
5/9/12/15/18/24V
Number Of Segments
1
Operating Temperature (min)
-40C
Operating Temperature (max)
125C
Operating Temperature Classification
Automotive
Package Type
MSOP
Pin Count
8
Mounting
Surface Mount
Power Dissipation
660mW
Operating Supply Voltage (min)
4.5V
Operating Supply Voltage (max)
35V
For Use With
LM3401EVAL - BOARD EVALUATION FOR LM3401
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Voltage - Output
-
Lead Free Status / Rohs Status
Compliant
Other names
LM3401MMTR
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Part Number:
LM3401MM/NOPB
Manufacturer:
NS/国半
Quantity:
20 000
www.national.com
to the sensed voltage at the CS pin. Current limit is activated
and latched when the voltage at the CS pin drops below the
voltage at the ILIM pin.
The current limit setting resistor, R3, can be calculated from
the equation below. The minimum current limit occurs at max-
imum R
Where 4 µA is the minimum I
inductor current limit threshold. I
what higher than the maximum LED current, I
false current limit triggering. The temperature variation of the
PFET R
limit. To ensure that current limit is not falsely triggered, use
the highest R
the R3 value.
When current limit is activated, the HG driver remains off until
the CS voltage rises to -130 mV (typical). This ensures that
inductor current is close to 0A when the current limit latch is
released. The actual minimum inductor current will depend on
the catch diode forward voltage characteristic, which deter-
mines the CS pin negative voltage.
Although the LM3401 monitors voltage at the CS pin to reset
the current limit, there is also a minimum off time of typically
3 µs. When current limit is triggered, HG will be turned off for
at least this amount of time, regardless of the inductor current.
The current limit comparator imposes typically 150 ns of
blanking time at the beginning of each switching cycle. This
ensures that the PFET is fully on and any switch node ringing
has dissipated when the current is sensed. However a slower
PFET may not fully turn on within the blanking time. In this
case, the current limit threshold must be increased or a faster
PFET must be used.
Because the current limit comparator has a limited differential
voltage capability, a maximum of 1MΩ is recommended for
R3.
PWM DIMMING
The DIM pin is a CMOS compatible input for a PWM (Pulse
Width Modulation) dimming signal. PWM dimming adjusts
LED brightness by varying the duty cycle, which varies the
average LED current. This type of dimming is recommended,
because LED peak current remains constant regardless of
brightness, which results in more predictable LED color and
performance as compared to analog dimming. Figure 7
shows a typical PWM dimming waveform.
When DIM is high (above 2V typically) the LM3401 operates
normally and the LED string will be driven at the set current.
When pulled low, DIM will disable HG and switching will stop.
The PFET will remain off as long as DIM is low. When the
LM3401 is powered up or enabled with the DIM pin, the LED
current will very rapidly increase to its set point.
There is minimal delay time between a DIM logic change and
HG switching. Also, because the LM3401 requires no output
capacitor, minimal time is required to ramp-up the LED cur-
rent. This allows for low duty cycle, high frequency PWM
dimming signals to be used.
A dimming frequency greater than 100 Hz is recommended
to avoid visible flicker. The LM3401 is capable of PWM dim-
ming frequencies up to 10 kHz with a duty cycle between 1
and 100%. Any DIM signal pulse width longer than 100 ns can
be used. In most cases, the maximum dimming frequency is
DS(on)
DS(on)
and minimum I
DS(on)
will result in an equivalent variation in current
value over the temperature range to set
ILIM
ILIM
value.
value and I
LIM_PK
should be set some-
LIM_PK
LED_PK
is the peak
, to avoid
10
limited by the inductor size and input voltage to anode voltage
ratio. Less inductance and higher V
the inductor and LED current to increase faster, thus allowing
for a faster PWM frequency, or lower dimming duty cycle.
DIM is a high impedance pin, which is somewhat sensitive to
noise. If there is excessive switching noise at the DIM pin, a
small bypass filter capacitor can be used. See the Ripple Re-
duction Capacitor section. V
dimming when a logic signal is not available. In this mode of
operation DIM should be connected to V
resistor. There is typically 10 us of startup delay time when
using V
lay limits the maximum dimming frequency to typically several
hundred Hz.
Higher dimming frequency and lower dimming duty cycle can
be achieved by using a FET switch in parallel with the LED
string. This is shown in Figure 8 below.
When the FET switches on, inductor current flows through the
FET and the regulated average inductor current is un-
changed. Using this method, inductor current rise time does
not limit the dimming frequency. A ripple reduction capacitor
should not be used with the parallel FET dimming method
since it significantly slows the LED current rise time. However,
a small noise filter capacitor can be used.
INPUT CAPACITOR SELECTION
An input bypass capacitor is required between V
ground. The input capacitor prevents large voltage transients
FIGURE 7. Typical PWM DIM Signal and LED Current
IN
for dimming. Depending on the application, this de-
FIGURE 8. Parallel FET Dimming
L = 22 µH
IN
can also be used for PWM
IN
/V
ANODE
IN
through a 10 kΩ
30021433
ratios will allow
30021434
IN
and