MIC2591B-2BTQ TR Micrel Inc, MIC2591B-2BTQ TR Datasheet - Page 20
![IC PCI HOT PLUG CTLR DUAL 48TQFP](/photos/6/84/68454/576-48-tqfp_sml.jpg)
MIC2591B-2BTQ TR
Manufacturer Part Number
MIC2591B-2BTQ TR
Description
IC PCI HOT PLUG CTLR DUAL 48TQFP
Manufacturer
Micrel Inc
Type
Hot-Swap Controllerr
Datasheet
1.MIC2591B-2YTQ.pdf
(34 pages)
Specifications of MIC2591B-2BTQ TR
Applications
General Purpose, PCI Express
Internal Switch(s)
No
Voltage - Supply
3.3V, 12V
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
48-TQFP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
MIC2591B-2BTQTR
MIC2591B-2BTQTR
MIC2591B-2BTQTR
overcurrent condition raise the junction temperature of one
slot’s controller and pass elements to 140°C, all of the outputs
for that slot (including VAUX) will be shut off and the slot’s
/FAULT output will be asserted. The other slot’s operating
condition will remain unaffected. However, should the
MIC2591B’s die temperature exceed 160°C, both slots (all
outputs, including VAUXA and VAUXB) will be shut off, whether
or not a current limit condition exists. A 160°C overtemperature
condition additionally sets the overtemperature bit (OT_INT)
in the Common Status Register.
/PWRGD[A/B] Outputs
The MIC2591B has two /PWRGD outputs, one for each slot.
These are open-drain, active-low outputs that require an
external pull-up resistor to V
when a slot has been enabled and has successfully begun
delivering power to its respective +12V, +3.3V, and VAUX
outputs. An equivalent logic diagram for /PWRGD[A/B] is
shown in Figure 8.
/FORCE_ON[A/B] Inputs
These level-sensitive, active-low inputs are provided to
facilitate designing systems using the MIC2591B. Asserting
/FORCE_ON[A/B] will turn on all three of the respective slot’s
outputs (+12V, +3.3V, and VAUX), while specifi cally defeating
all protections for those outputs. This explicitly includes all
overcurrent and short circuit protections, and on-chip ther-
mal protection for the VAUX outputs. Additionally, asserting
a slot’s /FORCE_ON[A/B] input will disable all of its input
and output UVLO protections, with the sole exception of that
asserting either or both of the /FORCE_ON[A/B] inputs will
not disable the VSTBY[A/B] input UVLO.
Asserting /FORCE_ON[A/B] will cause the respective slot’s
/PWRGD[A/B] and /FAULT[A/B] outputs to enter their open-
drain state. Additionally, there are two SMBus accessible
register bits (see CNTRL[A/B] Register Bit D[2]), which can
be set to disable the corresponding slot’s /FORCE_ON[A/B]
pins. This allows system software to prevent these hardware
overrides from being inadvertently activated during normal
use. If not used, each pin should be connected to V
an external pull-up resistor. See Figure 6 for details.
General Purpose Input (GPI) Pins
Two pins on the MIC2591B are available for use as GPI
pins. The logic state of each of these pins can be determined
by polling Bits [4:5] of Common Status Register. Both of
these inputs are compliant to 3.3V. If unused, connect each
GPI_[A0/B0] pin to GND.
A/D Converter
The MIC2591B has an internal 12-channel, 8-bit A/D converter
that monitors the output voltage and current of each supply.
This information is available via the System Management
Interface. While the information is particularly intended for
use by systems that support the IPMI 1.0 standard, it may
be used for any other desired purpose. A 23.2kΩ external
resistor must be connected from the IREF pin to ground to
set the A/D Converter's Full-Scale current reference for the
VAUX[A/B] internal MOSFETs.
March 2005
STBY
STBY
STBY
. Each output is asserted
. Each output is asserted
STBY
STBY
STBY
using
using
20
Hot-Plug Interface (HPI)
Once the input supplies are above their respective UVLO
thresholds, the Hot-Plug Interface can be utilized for power
control by enabling the control input pins (AUXEN[A/B] and
ON[A/B]) for each slot. In order for the MIC2591B to switch
on the VAUX supply for either slot, the AUXEN[A/B] control
must be enabled after the power-on-reset delay, t
cally, 250µs), has elapsed. The timing response diagram of
Figure 9 illustrates a Hot-Plug Interface operation where an
overcurrent fault is detected by the MIC2591B controller
after initiating a power-up sequence. The MAIN (+12V &
+3.3V) and VAUX[A/B] supply rails, /FAULT, /PWRGD and
/INT output responses for both AUX and MAIN are shown
in the fi gure.
System Management Interface (SMI)
The MIC2591B’s System Management Interface uses the
Read_Byte and Write_Byte subset of the SMBus protocols
to communicate with its host via the System Management
Interface bus. The /INT output signals the controlling proces-
sor that one or more events need attention, if an interrupt-
driven architecture is used. Note that the MIC2591B does
not participate in the SMBus Alert Response Address (ARA)
portion of the SMBus protocol.
Fault Reporting and Interrupt Generation
SMI-only Control Applications
In applications where the MIC2591B is controlled only by
the SMI, ON[A/B] and AUXEN[A/B] are connected to GND
and the /FORCE_ON[A/B] pins are connected to V
shown in Figure 6. In this case, the MIC2591B’s /FAULT[A/B]
outputs and STAT[A/B] Register Bit D[7] (FAULT[A/B])
are not activated as fault status is determined by polling
STAT[A/B] Register Bits D[4], D[2], D[0] and CS (Common
Status) Register Bits D[2:1]. Individual fault bits in STAT[A/B]
and CS registers are asserted after power-on-reset when:
To clear any one or all STAT[A/B] Register Bits D[4], D[2], D[0]
and/or CS Register Bits D[2], D[1] once asserted, a software
subroutine can perform an “echo reset” where a Logical “1” is
written back to those register bit locations that have indicated
a fault. This method of “echo reset” allows data to be retained
in the STAT[A/B] and/or CS registers until such time as the
system is prepared to operate on that data.
The MIC2591B can operate in interrupt mode or polled mode.
For interrupt-mode operation, the open-drain, active-LOW
/INT output signal is activated after power-on-reset if the
INTMSK bit (CS Register Bit D[3]) has been reset to Logical
“0”. Once activated, the /INT output is asserted by any one
• Either or both CNTRL[A/B] Register Bits D[1:0] are
• 12VIN[A/B], 3VIN[A/B], or VSTBY[A/B] input volt-
• The fast OC circuit breaker[A/B] has tripped, OR
• The slow OC circuit breaker[A/B] has tripped AND
• The slow OC circuit breaker[A/B] has tripped AND
• The MIC2591B’s global die temperature > 160°C
asserted, AND
age is lower than its respective ULVO threshold,
OR
its fi lter timeout has expired, OR
Slot[A/B] die temperature > 140°C, OR
M9999-033105
POR
STBY
STBY
STBY
(typi-
as
as