LTC4257CDD#TR Linear Technology, LTC4257CDD#TR Datasheet - Page 10
![IC CONTROLLER POE INTERFACE 8DFN](/photos/7/2/70256/161-8-dfn_sml.jpg)
LTC4257CDD#TR
Manufacturer Part Number
LTC4257CDD#TR
Description
IC CONTROLLER POE INTERFACE 8DFN
Manufacturer
Linear Technology
Type
Power over Ethernet Switch (PoE)r
Datasheet
1.LTC4257CS8PBF.pdf
(20 pages)
Specifications of LTC4257CDD#TR
Applications
IP Phones, Power over LAN, Network Routers and Switches
Internal Switch(s)
Yes
Current Limit
350mA
Operating Temperature
0°C ~ 70°C
Mounting Type
Surface Mount
Package / Case
8-WFDFN Exposed Pad
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
APPLICATIO S I FOR ATIO
LTC4257
is designed to accept this thermal load and is thermally
protected to avoid damage to the onboard power MOSFET.
Note that the PD designer must ensure that the PD steady-
state power consumption falls within the limits shown in
Table 2.
Power Good
The LTC4257 includes a power good circuit (Figure 6) that
is used to indicate to the PD circuitry that load capacitor C1
is fully charged and that the PD can start DC/DC converter
operation. The power good circuit monitors the voltage
across the internal power MOSFET and PWRGD is as-
serted when the voltage drops below 1.5V. The power
good circuit includes a large amount of hysteresis to allow
the LTC4257 to operate near the current limit point without
inadvertently disabling PWRGD. The MOSFET voltage
must increase to 3V before PWRGD is disabled.
If a sudden increase in voltage appears on the input line,
this voltage step will be transferred through capacitor C1
and appear across the power MOSFET. The response of
the LTC4257 will depend on the magnitude of the voltage
step, the rise time of the step, the value of capacitor C1 and
the DC load. For fast rising inputs, the LTC4257 will
attempt to quickly charge capacitor C1 using an internal
secondary current limit circuit. In this scenario, the PSE
current limit should provide the overall limit for the circuit.
For slower rising inputs, the 350mA current limit in the
LTC4257 will set the charge rate of capacitor C1. In either
case, the PWRGD signal may go inactive briefly while the
capacitor is charged up to the new line voltage. In the
10
U
PSE
U
TO
4
V
LTC4257
IN
W
Figure 6. LTC4257 Power Good
U
THERMAL SHUTDOWN
UVLO
–
+
design of a PD, it is necessary to determine if a step in the
input voltage will cause the PWRGD signal to go inactive
and how to respond to this event. In some designs, the
charge on C1 is sufficient to power the PD through this
event. In this case, it may be desirable to filter the PWRGD
signal so that intermittent power bad conditions are
ignored. Figure 10 demonstrates methods to insert a
lowpass filter on the power good interface.
For PD designs that use a large load capacitor and also
consume a lot of power, it is important to delay activation
of the PD circuitry with the PWRGD signal. If the PD cir-
cuitry is not disabled during the current-limited turn-on se-
quence, the PD circuitry will rob current intended for charg-
ing up the load capacitor and create a slow rising input,
possibly causing the LTC4257 to go into thermal shutdown.
The PWRGD pin connects to an internal open-drain, 100V
transistor capable of sinking 1mA. Low impedance indi-
cates power is good. PWRGD is high impedance during
signature and classification probing and in the event of a
thermal overload.
During turn-off, PWRGD is deactivated when the input
voltage drops below 30V. In addition, PWRGD may go
active briefly at turn-on for fast rising input waveforms.
PWRGD is referenced to the V
be near the V
typically be referenced to V
ensure that the difference in potential of the PWRGD signal
does not cause any detrimental effects. Use of diode clamp
D6, as shown in Figure 10, will alleviate any problems.
+
–
1.125V
300k
PWRGD
300k
V
OUT
IN
6
5
MIN
potential. The PD DC/DC converter will
5µF
C1
R9
100k
+
SHDN
LOAD
PD
4257 F06
OUT
IN
and care must be taken to
pin and when active will
4257fb