ADE7753ARSZ Analog Devices Inc, ADE7753ARSZ Datasheet - Page 9

• Manufacturer Part Number: ADE7753ARSZ
• Description: IC ENERGY METERING 1PHASE 20SSOP
• Manufacturer: Analog Devices Inc

Specifications of ADE7753ARSZ

• Input Impedance: 390 KOhm
• Measurement Error: 0.1%
• Voltage - I/o High: 2.4V
• Voltage - I/o Low: 0.8V
• Current - Supply: 3mA
• Voltage - Supply: 4.75 V ~ 5.25 V
• Operating Temperature: -40°C ~ 85°C
• Mounting Type: Surface Mount
• Package / Case: 20-SSOP (0.200", 5.30mm Width)
• Meter Type: Single Phase
• Ic Function: Single-Phase Multifunction Metering IC
• Supply Voltage Range: 4.75V To 5.25V
• Operating Temperature Range: -40°C To +85°C
• Digital Ic Case Style: SSOP
• No. Of Pins: 20
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• For Use With: EVAL-ADE7753ZEB - BOARD EVALUATION AD7753
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant

Pin No.
12
13
14
15
16
17
18
19
20
Mnemonic
ZX
SAG
IRQ
CLKIN
CLKOUT
CS
SCLK
DOUT
DIN
Description
Voltage Waveform (Channel 2) Zero-Crossing Output. This output toggles logic high and logic low at the
zero crossing of the differential signal on Channel 2—see the Zero-Crossing Detection section.
This open-drain logic output goes active low when either no zero crossings are detected or a low voltage
threshold (Channel 2) is crossed for a specified duration—see the Line Voltage Sag Detection section.
Interrupt Request Output. This is an active low open-drain logic output. Maskable interrupts include active
energy register rollover, active energy register at half level, and arrivals of new waveform samples—see the
ADE7753 Interrupts section.
Master Clock for ADCs and Digital Signal Processing. An external clock can be provided at this logic input.
Alternatively, a parallel resonant AT crystal can be connected across CLKIN and CLKOUT to provide a clock
source for the ADE7753. The clock frequency for specified operation is 3.579545 MHz. Ceramic load
capacitors of between 22 pF and 33 pF should be used with the gate oscillator circuit. Refer to the crystal
manufacturer’s data sheet for load capacitance requirements.
A crystal can be connected across this pin and CLKIN as described for Pin 15 to provide a clock source for
the ADE7753. The CLKOUT pin can drive one CMOS load when either an external clock is supplied at CLKIN
or a crystal is being used.
Chip Select. Part of the 4-wire SPI serial interface. This active low logic input allows the ADE7753 to share
the serial bus with several other devices—see the ADE7753 Serial Interface section.
Serial Clock Input for the Synchronous Serial Interface. All serial data transfers are synchronized to this
clock—see the ADE7753 Serial Interface section. The SCLK has a Schmitt-trigger input for use with a clock
source that has a slow edge transition time, for example, opto-isolator output.
Data Output for the Serial Interface. Data is shifted out at this pin on the rising edge of SCLK. This logic
output is normally in a high impedance state unless it is driving data onto the serial data bus—see the
ADE7753 Serial Interface section.
Data Input for the Serial Interface. Data is shifted in at this pin on the falling edge of SCLK—see the
ADE7753 Serial Interface section.
Rev. A | Page 9 of 60
ADE7753