A4401KL-T Allegro Microsystems Inc, A4401KL-T Datasheet - Page 12

• Manufacturer Part Number: A4401KL-T
• Description: IC QUASI FLYBACK CONVERTER 8SOIC
• Manufacturer: Allegro Microsystems Inc

Specifications of A4401KL-T

• Display Type: Vacuum Fluorescent (VF)
• Current - Supply: 2.3mA
• Voltage - Supply: 7 V ~ 40 V
• Operating Temperature: -40°C ~ 125°C
• Mounting Type: Surface Mount
• Package / Case: 8-SOIC (3.9mm Width)
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Interface: -
• Configuration: -
• Digits Or Characters: -

A4401
where I
is the duty cycle, limited to 0.3.
Then the rms current in the winding is:
Because the number of turns has already been worked
out, the ampere-turns factor can now be determined.
After all of the ampere-turns are known for each wind-
ing, the bobbin window can be apportioned to each
winding. It is recommended that the current density in
each winding should be kept below 5 A per mm
Another consideration when selecting the wire gauge
is the skin depth (depth within which the current
flows), especially at higher frequencies. Skin depth
can be calculated as:
For example, if 45 kHz were the minimum frequency
at minimum input voltage and maximum load, then
to ensure maximum wire utilization for the first four
switching harmonics, the switching frequency would
be 180 kHz. The conduction depth at 180 kHz would
equal 0.18 mm, therefore, the wire diameter should
not exceed 0.36 mm. For any particular winding, if the
current rating of the wire is insufficient even though
the wire meets the skin depth criteria, multiple wires
wound in parallel will be necessary.
It is recommended to locate the start and finish of
each winding as close as possible on the bobbin. This
minimizes the “loop area” and reduces the effects of
noise pick-up.
When winding the high voltage windings, such as for
the anode or grid, it is advisable to insert a layer of
polyester insulating tape between each layer as well as
between adjacent windings.
OUT
is the maximum load current, and D'(max)
I
RMS
=
δ =
I
PK
×
f
⎛
⎜ ⎜
⎝
75
½
SW
D'
3
Automotive Quasi-Resonant Flyback Control IC
⎞
⎟ ⎟
⎠
½
,
,
2
.
(32)
(33)
C11 Resonant Capacitor Selection
The resonance that occurs when the MOSFET, Q1,
turns off is formed by the interaction of the primary
magnetizing inductance and the capacitance between
the LX node (the drain terminal of the MOSFET) and
ground. The design is optimized for a half resonant
period of 1 μs. This means the resonant capacitor
value can be found from the following formula:
where T
It is advisable to measure the half resonant period in
the application, as the parasitic capacitance between
the LX node and ground can be substantial and may
even be sufficient to meet the requirements with very
little additional capacitance.
PCB Layout Guidelines
The layout can be considered as two blocks: primary
and secondary:
Primary Block
on the ground return, and at the LX and ISS nodes,
as well as to maximize the effectiveness of the EMI
Figure 3. Main power loop
V
R
BAT
C
is a half resonant period of 1 μs.
IN
To minimize parasitic noise appearing
C
RES
=
115 Northeast Cutoff, Box 15036
Allegro MicroSystems, Inc.
Worcester, Massachusetts 01615-0036 [phone]
www.allegromicro.com
⎛
⎜ ⎜
⎝
A4401
T
L
R
PRI
⎞
⎟ ⎟
⎠
²
×
L
Minimize this loop area
PRI
1
,
MOSFET
Q1
LX node
ISS node
R
SENSE
(34)
12