LTC4151IMS#PBF Linear Technology, LTC4151IMS#PBF Datasheet - Page 6
![IC CURRENT MONITOR(12BIT) 10MSOP](/photos/1/36/13608/10-msop_05-08-1661_sml.jpg)
LTC4151IMS#PBF
Manufacturer Part Number
LTC4151IMS#PBF
Description
IC CURRENT MONITOR(12BIT) 10MSOP
Manufacturer
Linear Technology
Specifications of LTC4151IMS#PBF
Function
Current Monitor (12 Bit)
Sensing Method
High-Side
Accuracy
±1%
Voltage - Input
7 ~ 80 V
Operating Temperature
-40°C ~ 85°C
Mounting Type
Surface Mount
Package / Case
10-MSOP, Micro10™, 10-uMAX, 10-uSOP
Voltage Supervisor Type
Voltage Monitor
Number Of Voltage Supervisors
1
Reset Threshold Voltage (min)
2.3V
Reset Threshold Voltage (max)
2.9V
Operating Supply Voltage (min)
7V
Operating Supply Voltage (max)
80V
Package Type
MSOP
Operating Temperature Classification
Industrial
Operating Temp Range
-40C to 85C
Pin Count
10
Mounting
Surface Mount
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Current - Output
-
Lead Free Status / Rohs Status
Compliant
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
LTC4151
TYPICAL PERFORMANCE CHARACTERISTICS
PIN FUNCTIONS
SENSE
recommended Kelvin connection.
V
at this pin is monitored by the onboard ADC with a full-
scale input range of 102.4V. SENSE
to V
ADR1, ADR0: I
ADR1 and ADR0 to V
confi gures one of nine possible addresses. See Table 1
in the Applications Information section for details.
ADIN: ADC Input. The onboard ADC measures voltage
range between 0V and 2.048V. Tie to GND if unused.
SCL: I
the SDA pin on rising edges of SCL. This pin is driven
by an open-collector output from a master controller. An
external pull-up resistor or current source is required and
can be placed between SCL and V
is internally clamped to 6V (5.5V minimum).
SDA (LTC4151 Only): I
shifting in address, command or data bits and sending
out data. An external pull-up resistor or current source
6
IN
: Supply Voltage Input. Accepts 7V to 80V. The voltage
IN
2
for proper ADC readout.
+
C Bus Clock Input. Data is shifted in and out at
: Kelvin Sense of the V
0.5
0.4
0.3
0.2
0.1
2
0
C Device Address Inputs. Connecting
0
SDA, SDAO, SDAO Output Low vs
Pull-Up Current (V
2
IN
C Bus Data Input/Output. Used for
, GND or leaving the pins open
5
I
SDA
IN
10
(mA)
Pin. See Figure 10 for
SDA(OL)
IN
+
. The voltage at SCL
must be connected
15
vs I
– 40°C
SDA
4151 G09
85°C
25°C
)
20
is required and can be placed between SDA and V
The voltage at SDA is internally clamped to 6V (5.5V
minimum).
SDAI (LTC4151-1/LTC4151-2 Only): I
Used for shifting in address, command or data bits. This
pin is driven by an open-collector output from a master
controller. An external pull-up resistor or current source is
required and can be placed between SDAI and V
age at SDAI is internally clamped to 6V (5.5V minimum).
SDAO (LTC4151-2 Only): Serial Bus Data Output. Open-
drain output used for sending data back to the master
controller or acknowledging a write operation. Normally
tied to SDAI to form the SDA line. An external pull-up
resistor or current source is required.
SDAO (LTC4151-1 Only): Inverted Serial Bus Data Out-
put. Open-drain output used for sending data back to the
master controller or acknowledging a write operation. Data
is inverted for convenience of opto-isolation. An external
pull-up resistor or current source is required.
SHDN (LTC4151 Only): Shutdown Input. Internally pulled
up to 6.3V. Pull this pin below 1V to force the LTC4151 into
shutdown mode. Leave this pin open if unused.
6.1
6.0
5.9
6.3
6.2
0.01
SDA, SDAI, SCL Clamp Voltage
vs Load Current
– 40°C
85°C
V
IN
= 12V, T
25°C
0.1
I
LOAD
A
= 25°C, unless noted.
(mA)
1
4151 G10
2
10
C Bus Data Input.
IN
. The volt-
4151fb
IN
.