M29F800DB70N6 NUMONYX, M29F800DB70N6 Datasheet - Page 18
![no-image](/images/manufacturer_photos/0/4/484/numonyx_sml.jpg)
M29F800DB70N6
Manufacturer Part Number
M29F800DB70N6
Description
IC FLASH 8MBIT 70NS 48TSOP
Manufacturer
NUMONYX
Datasheet
1.M29F800DB70N6.pdf
(53 pages)
Specifications of M29F800DB70N6
Format - Memory
FLASH
Memory Type
FLASH - Nor
Memory Size
8M (1M x 8 or 512K x 16)
Speed
70ns
Interface
Parallel
Voltage - Supply
4.5 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
48-TSOP
Lead Free Status / RoHS Status
Contains lead / RoHS non-compliant
Other names
497-1710
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M29F800DB70N6
Manufacturer:
ST
Quantity:
1 760
Company:
Part Number:
M29F800DB70N6
Manufacturer:
ST
Quantity:
2 000
Command Interface
4.0.7
4.0.8
18/53
Chip Erase command
The Chip Erase command can be used to erase the entire chip. Six Bus Write operations
are required to issue the Chip Erase Command and start the Program/Erase Controller.
If any blocks are protected then these are ignored and all the other blocks are erased. If all
of the blocks are protected the Chip Erase operation appears to start but will terminate
within about 100µs, leaving the data unchanged. No error condition is given when protected
blocks are ignored.
During the erase operation the memory will ignore all commands. It is not possible to issue
any command to abort the operation. Typical chip erase times are given in
Read operations during the Chip Erase operation will output the Status Register on the Data
Inputs/Outputs. See
After the Chip Erase operation has completed the memory will return to the Read Mode,
unless an error has occurred. When an error occurs the memory will continue to output the
Status Register. A Read/Reset command must be issued to reset the error condition and
return to Read Mode.
The Chip Erase Command sets all of the bits in unprotected blocks of the memory to ’1’. All
previous data is lost.
Block Erase command
The Block Erase command can be used to erase a list of one or more blocks. Six Bus Write
operations are required to select the first block in the list. Each additional block in the list can
be selected by repeating the sixth Bus Write operation using the address of the additional
block. The Block Erase operation starts the Program/Erase Controller about 50µs after the
last Bus Write operation. Once the Program/Erase Controller starts it is not possible to
select any more blocks. Each additional block must therefore be selected within 50µs of the
last block. The 50µs timer restarts when an additional block is selected. The Status Register
can be read after the sixth Bus Write operation. See the Status Register for details on how
to identify if the Program/Erase Controller has started the Block Erase operation.
If any selected blocks are protected then these are ignored and all the other selected blocks
are erased. If all of the selected blocks are protected the Block Erase operation appears to
start but will terminate within about 100µs, leaving the data unchanged. No error condition is
given when protected blocks are ignored.
During the Block Erase operation the memory will ignore all commands except the Erase
Suspend command. Typical block erase times are given in
during the Block Erase operation will output the Status Register on the Data Inputs/Outputs.
See
After the Block Erase operation has completed the memory will return to the Read Mode,
unless an error has occurred. When an error occurs the memory will continue to output the
Status Register. A Read/Reset command must be issued to reset the error condition and
return to Read mode.
The Block Erase Command sets all of the bits in the unprotected selected blocks to ’1’. All
previous data in the selected blocks is lost.
Section 5: Status
Section 5: Status
Register, for more details.
Register, for more details.
Table
6. All Bus Read operations
Table
M29F800DT
6. All Bus