AT45DB161D-SU Atmel, AT45DB161D-SU Datasheet - Page 17

• Manufacturer Part Number: AT45DB161D-SU
• Description: IC FLASH 16MBIT 66MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT45DB161D-SU

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 16M (4096 pages x 528 bytes)
• Speed: 66MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (5.3mm Width), 8-SOP, 8-SOEIAJ
• Architecture: Sectored
• Interface Type: SPI
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 2.7 V
• Maximum Operating Current: 15 mA
• Mounting Style: SMD/SMT
• Organization: 128 KB x 16
• Current, Input, Leakage: 1 μA
• Current, Operating: 11 mA (Read), 12 mA (Program/Erase)
• Current, Output, Leakage: 1
• Data Retention: 20 yrs.
• Density: 16M
• Package Type: EIAJ SOIC
• Temperature, Operating: -40 to +85 °C
• Time, Access: 6 ns
• Time, Address Hold: 5
• Time, Address Setup: 5
• Time, Fall: 6.8 ns
• Time, Rise: 6.8 ns
• Voltage, Input, High: 1.89 to 2.52 V
• Voltage, Input, Low: 0.81 to 1.08 V
• Voltage, Output, High: 2.5 V
• Voltage, Output, Low: 0.4 V
• Voltage, Supply: 2.7 to 3.6 V
• Memory Configuration: 4096 Pages X 528 Bytes
• Clock Frequency: 66MHz
• Supply Voltage Range: 2.5V To 3.6V, 2.7V To 3.6V
• Rohs Compliant: Yes
• Access Time (max): 6ns
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3/3.3V
• Operating Temp Range: -40C to 85C
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Supply Current: 15mA
• Mounting: Surface Mount
• Pin Count: 8
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

9.1.3
Figure 9-4.
9.1.4
3500I–DFLASH–8/07
CS
SO
Read Sector Protection Register Command
SI
Various Aspects About the Sector Protection Register
Read Sector Protection Register
Each transition
represents 8 bits
Opcode
To read the Sector Protection Register, the CS pin must first be asserted. Once the CS pin has
been asserted, an opcode of 32H and 3 dummy bytes must be clocked in via the SI pin. After the
last bit of the opcode and dummy bytes have been clocked in, any additional clock pulses on the
SCK pins will result in data for the content of the Sector Protection Register being output on the
SO pin. The first byte corresponds to sector 0 (0a, 0b), the second byte corresponds to sector 1
and the last byte (byte 16) corresponds to sector 15. Once the last byte of the Sector Protection
Register has been clocked out, any additional clock pulses will result in undefined data being
output on the SO pin. The CS must be deasserted to terminate the Read Sector Protection Reg-
ister operation and put the output into a high-impedance state.
Note:
The Sector Protection Register is subject to a limit of 10,000 erase/program cycles. Users are
encouraged to carefully evaluate the number of times the Sector Protection Register will be
modified during the course of the applications’ life cycle. If the application requires that the Sec-
tor Protection Register be modified more than the specified limit of 10,000 cycles because the
application needs to temporarily unprotect individual sectors (sector protection remains enabled
while the Sector Protection Register is reprogrammed), then the application will need to limit this
practice. Instead, a combination of temporarily unprotecting individual sectors along with dis-
abling sector protection completely will need to be implemented by the application to ensure that
the limit of 10,000 cycles is not exceeded.
Command
Read Sector Protection Register
xx = Dummy Byte
X
X
X
Data Byte
Byte 1
32H
n
Data Byte
n + 1
Byte 2
xxH
AT45DB161D
Byte 3
Data Byte
xxH
n + 15
Byte 4
xxH
17