AT49F2048A-70TC Atmel, AT49F2048A-70TC Datasheet
AT49F2048A-70TC
Specifications of AT49F2048A-70TC
Available stocks
Related parts for AT49F2048A-70TC
AT49F2048A-70TC Summary of contents
Page 1
... Active Current – 100 µA CMOS Standby Current • Typical 10,000 Write Cycles Description The AT49F2048A is a 5-volt-only, 2-megabit Flash memory organized as 262,144 words of 8 bits each or 128K words of 16 bits each. Manufactured with Atmel’s Pin Configurations Pin Name Function ...
Page 2
... When deselected, the CMOS standby current is less than 100 µA. To allow for simple in-system reprogrammability, the AT49F2048A does not require high input voltages for pro- gramming. Five-volt-only commands determine the read and programming operation of the device. Reading data out of the device is similar to reading from an EPROM; it has standard CE, OE and WE inputs to avoid bus connec- tion ...
Page 3
... Product Identification Entry/Exit” on page 10. The manufacturer and device codes are the same for both modes. DATA POLLING: The AT49F2048A features Data Polling to indicate the end of a program cycle. During a program cycle time. The Data Polling feature may ...
Page 4
... Data Polling may begin at any time during the program cycle. TOGGLE BIT: In addition to Data Polling, the AT49F2048A provides another method for determining the end of a pro- gram or erase cycle. During a program or erase operation, successive attempts to read data from the device will result in I/O6 toggling between one and zero ...
Page 5
... A16 = VIL A16 = VIL A16 = Condition MHz OUT -400 µ -100 µ AT49F2048A AT49F2048A-90 0°C - 70°C -40°C - 85°C 5V ± 10 OUT High-Z High-Z X High-Z ( Manufacturer Code ( Device Code Manufacturer Code A16 = V Device Code IH IL Min CC 2.0 2.4 = 4.5V 4.2 ...
Page 6
... This parameter is characterized and is not 100% tested. AT49F2048A 6 AT49F2048A-70 Min 0 0 ADDRESS VALID ACC HIGH Z OUTPUT VALID - t after the address transition without impact after the falling edge of CE without impact Max Units AT49F2048A-90 Max Min Max ACC after an address change CE ACC OE Output Test Load 30 Conditions V ...
Page 7
AC Word Load Characteristics Symbol Parameter Address, OE Setup Time AS OES t Address Hold Time AH t Chip Select Setup Time CS t Chip Select Hold Time CH t Write Pulse Width (WE or CE) WP ...
Page 8
... OE must be high only when WE and CE are both low. 2. For chip erase, the address should be 5555. For sector erase, the address depends on what sector erased. (See note 4 under Command Definitions.) 3. For chip erase, the data should be 10H, and for sector erase, the data should be 30H. AT49F2048A 8 PROGRAM CYCLE ...
Page 9
... Beginning and ending state of I/O6 will vary. 3. Any address location may be used but the address should not vary. 1159F–04/01 (1) t OEH HIGH ( OEH OEHP HIGH Z AT49F2048A Min Typ Max Min Typ Max 10 10 150 specification must be met by the toggling OEHP Units ns ns ...
Page 10
... The device does not remain in identification mode if powered down. 4. The device returns to standard operation mode. 5. Manufacturer Code: 001FH Device Code: 0082H 6. Either one of the Product ID Exit commands can be used. AT49F2048A 10 (1) Boot Block Lockout Enable Algorithm (1)(6) LOAD DATA F0 TO ANY ADDRESS EXIT PRODUCT ...
Page 11
... Wide, Plastic Gull Wing Small Outline Package (SOIC/SOP) 48T 48-lead, Thin Small Outline Package (TSOP) 1159F–04/01 Ordering Code AT49F2048A-70RC AT49F2048A-70TC AT49F2048A-70RI AT49F2048A-70TI AT49F2048A-90RC AT49F2048A-90TC AT49F2048A-90RI AT49F2048A-90TI Package Type AT49F2048A Package Operation Range 44R Commercial 48T (0° ...
Page 12
... Packaging Information 44R, 44-lead, 0.525" Wide, Plastic Gull Wing Small Outline (SOIC) Dimensions in Inches and (Millimeters) AT49F2048A 12 48T, 48-lead, Plastic Thin Small Outline Package (TSOP) Dimensions in Millimeters and (Inches) * JEDEC OUTLINE MO-142 DD *Controlling dimension: millimeters 1159F–04/01 ...
Page 13
... No licenses to patents or other intellectual property of Atmel are granted by the Company in connection with the sale of Atmel products, expressly or by implication. Atmel’s products are not authorized for use as critical components in life support devices or systems. ...