CAT25128LI-G ON Semiconductor, CAT25128LI-G Datasheet - Page 5

• Manufacturer Part Number: CAT25128LI-G
• Description: IC EEPROM 128KBIT 10MHZ 8DIP
• Manufacturer: ON Semiconductor

Specifications of CAT25128LI-G

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 128K (16K x 8)
• Speed: 10MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 1.8 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-DIP (0.300", 7.62mm)
• Density: 128Kb
• Interface Type: Serial (SPI)
• Organization: 16Kx8
• Access Time (max): 75ns
• Frequency (max): 5MHz
• Write Protection: Yes
• Data Retention: 100Year
• Operating Supply Voltage (typ): 2.5/3.3/5V
• Operating Temp Range: -40C to 85C
• Supply Current: 4mA
• Operating Supply Voltage (min): 1.8V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Through Hole
• Pin Count: 8
• Maximum Clock Frequency: 10 MHz
• Access Time: 75 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 1.8 V
• Maximum Operating Current: 4 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: Through Hole
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 3.3 V, 5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 25128LI-G

Status Register
number of status and control bits.
with a write operation. This bit is automatically set to 1 during
an internal write cycle, and reset to 0 when the device is ready
to accept commands. For the host, this bit is read only.
WREN/WRDI commands. When set to 1, the device is in a
Write Enable state and when set to 0, the device is in a Write
Disable state.
blocks are currently write protected. They are set by the user
with the WRSR command and are non−volatile. The user is
Table 8. STATUS REGISTER
Table 9. BLOCK PROTECTION BITS
Table 10. WRITE PROTECT CONDITIONS
The Status Register, as shown in Table 8, contains a
The RDY (Ready) bit indicates whether the device is busy
The WEL (Write Enable Latch) bit is set/reset by the
The BP0 and BP1 (Block Protect) bits determine which
WPEN
7
WPEN
BP1
X
X
0
0
1
1
0
0
1
1
Status Register Bits
6
0
High
High
Low
Low
WP
BP0
X
X
0
1
0
1
5
0
WEL
0
1
0
1
0
1
Array Address Protected
http://onsemi.com
4
0
3000−3FFF
2000−3FFF
0000−3FFF
None
5
Protected Blocks
allowed to protect a quarter, one half or the entire memory,
by setting these bits according to Table 9. The protected
blocks then become read−only.
the WP pin. Hardware write protection is enabled when the
WP pin is low and the WPEN bit is 1. This condition
prevents writing to the status register and to the block
protected sections of memory. While hardware write
protection is active, only the non−block protected memory
can be written. Hardware write protection is disabled when
the WP pin is high or the WPEN bit is 0. The WPEN bit, WP
pin and WEL bit combine to either permit or inhibit Write
operations, as detailed in Table 10.
Protected
Protected
Protected
Protected
Protected
Protected
The WPEN (Write Protect Enable) bit acts as an enable for
BP1
3
Unprotected Blocks
BP0
2
Protected
Protected
Protected
Writable
Writable
Writable
Quarter Array Protection
Half Array Protection
Full Array Protection
No Protection
Protection
WEL
1
Status Register
Protected
Protected
Protected
Protected
Writable
Writable
RDY
0