MT46H64M16LFCK-6:A TR Micron Technology Inc, MT46H64M16LFCK-6:A TR Datasheet - Page 13
![IC DDR SDRAM 1GBIT 60VFBGA](/photos/7/23/72339/60vfbga-package_sml.jpg)
MT46H64M16LFCK-6:A TR
Manufacturer Part Number
MT46H64M16LFCK-6:A TR
Description
IC DDR SDRAM 1GBIT 60VFBGA
Manufacturer
Micron Technology Inc
Datasheet
1.MT46H64M16LFCK-5A_TR.pdf
(95 pages)
Specifications of MT46H64M16LFCK-6:A TR
Format - Memory
RAM
Memory Type
Mobile DDR SDRAM
Memory Size
1G (64M x 16)
Speed
166MHz
Interface
Parallel
Voltage - Supply
1.7 V ~ 1.95 V
Operating Temperature
0°C ~ 70°C
Package / Case
60-VFBGA
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
557-1336-2
PDF: 09005aef82ce3074
1gb_ddr_mobile_sdram_t48m.pdf - Rev. K 07/09 EN
Table 3: VFBGA Ball Descriptions
LDQS, UDQS
RAS#, CAS#,
UDM, LDM
BA0, BA1
DQ[15:0]
DQ[31:0]
DQS[3:0]
Symbol
(60-ball)
DM[3:0]
(90-ball)
(60-ball)
(90-ball)
(60-ball)
(90-ball)
(60-ball)
(90-ball)
CK, CK#
A[13:0]
A[12:0]
WE#
CKE
CS#
output
output
Input/
Input/
Type
Input
Input
Input
Input
Input
Input
Input
Description
Clock: CK is the system clock input. CK and CK# are differential clock
inputs. All address and control input signals are sampled on the cross-
ing of the positive edge of CK and the negative edge of CK#. Input
and output data is referenced to the crossing of CK and CK# (both
directions of the crossing).
Clock enable: CKE HIGH activates, and CKE LOW deactivates, the in-
ternal clock signals, input buffers, and output drivers. Taking CKE
LOW enables PRECHARGE power-down and SELF REFRESH opera-
tions (all banks idle), or ACTIVE power-down (row active in any
bank). CKE is synchronous for all functions except SELF REFRESH ex-
it. All input buffers (except CKE) are disabled during power-down
and self refresh modes.
Chip select: CS# enables (registered LOW) and disables (registered
HIGH) the command decoder. All commands are masked when CS#
is registered HIGH. CS# provides for external bank selection on sys-
tems with multiple banks. CS# is considered part of the command
code.
Command inputs: RAS#, CAS#, and WE# (along with CS#) define the
command being entered.
Input data mask: DM is an input mask signal for write data. Input
data is masked when DM is sampled HIGH along with that input da-
ta during a WRITE access. DM is sampled on both edges of DQS.
Although DM balls are input-only, the DM loading is designed to
match that of DQ and DQS balls.
Bank address inputs: BA0 and BA1 define to which bank an ACTIVE,
READ, WRITE, or PRECHARGE command is being applied. BA0 and
BA1 also determine which mode register is loaded during a LOAD
MODE REGISTER command.
Address inputs: Provide the row address for ACTIVE commands, and
the column address and auto precharge bit (A10) for READ or
WRITE commands, to select one location out of the memory array in
the respective bank. During a PRECHARGE command, A10 deter-
mines whether the PRECHARGE applies to one bank (A10 LOW,
bank selected by BA0, BA1) or all banks (A10 HIGH). The address in-
puts also provide the op-code during a LOAD MODE REGISTER com-
mand.
Data input/output: Data bus for x16 and x32.
Data strobe: Output with read data, input with write data. DQS is
edge-aligned with read data, center-aligned in write data. It is used
to capture data.
13
1Gb: x16, x32 Mobile LPDDR SDRAM
Micron Technology, Inc. reserves the right to change products or specifications without notice.
Ball Assignments and Descriptions
©2007 Micron Technology, Inc. All rights reserved.