AMIS30585GEVK ON Semiconductor, AMIS30585GEVK Datasheet - Page 11

• Manufacturer Part Number: AMIS30585GEVK
• Description: Power Management IC Development Tools EVK PLC MODEM 1200 BAUD
• Manufacturer: ON Semiconductor
• Type: Supervisory Circuitsr

Specifications of AMIS30585GEVK

• Rohs: yes
• Product: Evaluation Kits
• Tool Is For Evaluation Of: AMIS-30585
• Input Voltage: 3 V to 3.6 V
• Output Voltage: 0.3 V

Oscillator: Pin XIN, XOUT
the static parameters and the inversion from XIN to XOUT in order to guarantee the functionality of the oscillator.
8. For the design of the oscillator crystal parameters have been taken from the data sheet [8]. The series loss resistance for this type of crystal
9. Measured relative to VSS.
10. These parameters will not be measured in production since the performance is totally dependent of a digital circuit which will be guaranteed
Table 8. OSCILLATOR
Table 9. ZERO CROSSING DETECTOR AND 50/60HZ PLL: Pin M50HZ_IN
Jitter
Parameter
In production the actual oscillation of the oscillator and duty cycle will not be tested. The production test will be based on
VOH
VOL
VIRM
VIFM
VIH
VIL
Parameter
VHY
is maximum 50 W. However the oscillator cell has been designed with some margin for series loss resistance up to 80 W.
by the digital test patterns.
CL
M50HZIN
M50HZIN
Flock
Flock
Tlock
Tlock
T
Imaxavg
V
DF
DF
startup
f
Imaxp
CLK
XOUT
MAINS
XOUT
CHIP_CLK
XOUT
XOUT
XOUT
50HZIN
60Hz
50Hz
50HZIN
50HZIN
50Hz
60Hz
50Hz
60Hz
Crystal frequency
Duty cycle with quartz connected
Start−up time
Maximum Capacitive load on XOUT
Low input threshold voltage
High input threshold voltage
Low output voltage
High input voltage
Maximum peak input current
Maximum average input current
during 1 ms
Mains voltage (ms) range
Rising threshold level
Falling threshold level
Hysteresis
Lock range for 50 Hz (Note 10)
Lock range for 60 Hz (Note 10)
Lock time (Note 10)
Lock time (Note 10)
Frequency variation without going
out of lock (Note 10)
Frequency variation without going
out of lock (Note 10)
Jitter of CHIP_CLK (Note 10)
Description
Description
XIN used as clock input
XIN used as clock input
XIN used as clock input
XIN used as clock input, XOUT = 2 mA
XIN used as clock input
http://onsemi.com
With protection resistor at M50HZIN
MAINS_FREQ = 0 (50 Hz)
MAINS_FREQ = 0 (60 Hz)
MAINS_FREQ = 0 (50 Hz)
MAINS_FREQ = 0 (60 Hz)
MAINS_FREQ = 0 (50 Hz)
MAINS_FREQ = 0 (60 Hz)
11
Condition
(Note 8)
(Note 8)
(Note 8)
Condition
(Note 9)
(Note 9)
(Note 9)
−100 ppm
−0.3 VDD
24 MHz
Min.
Min.
−20
−60
0.9
0.4
30
−2
90
45
54
+100 ppm
VDD−0.3
24 MHz
0.7 vdd
Max.
Max.
550
0.3
1.9
0.1
0.1
70
50
50
20
55
66
10
10
60
2
Unit
Unit
Hz/s
Hz/s
mA
mA
Ms
ms
pF
Hz
Hz
%
V
V
V
V
V
V
V
V
S
S