MT48LC8M16A2P-75:G Micron Technology Inc, MT48LC8M16A2P-75:G Datasheet - Page 21

• Manufacturer Part Number: MT48LC8M16A2P-75:G
• Description: IC SDRAM 128MBIT 133MHZ 54TSOP
• Manufacturer: Micron Technology Inc
• Type: SDRAMr

Specifications of MT48LC8M16A2P-75:G

• Memory Type: SDRAM
• Format - Memory: RAM
• Memory Size: 128M (8Mx16)
• Speed: 133MHz
• Interface: Parallel
• Voltage - Supply: 3 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Package / Case: 54-TSOP II
• Memory Configuration: 16M X 8
• Access Time: 5.4ns
• Page Size: 128Mbit
• Memory Case Style: TSOP
• No. Of Pins: 54
• Operating Temperature Range: 0°C To +70°C
• Organization: 8Mx16
• Density: 128Mb
• Address Bus: 14b
• Access Time (max): 6/5.4ns
• Maximum Clock Rate: 133MHz
• Operating Supply Voltage (typ): 3.3V
• Package Type: TSOP-II
• Operating Temp Range: 0C to 70C
• Operating Supply Voltage (max): 3.6V
• Operating Supply Voltage (min): 3V
• Supply Current: 150mA
• Pin Count: 54
• Mounting: Surface Mount
• Operating Temperature Classification: Commercial
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Compliant, Lead free / RoHS Compliant

Figure 9:
READs
PDF: 09005aef80725c0b/Source: 09005aef806fc13c
64MSDRAM_2.fm - Rev. M 10/07 EN
Example: Meeting
READ bursts are initiated with a READ command, as shown in Figure 10 on page 22.
The starting column and bank addresses are provided with the READ command, and
auto precharge is either enabled or disabled for that burst access. If auto precharge is
enabled, the row being accessed is precharged at the completion of the burst. For the
generic READ commands used in the following illustrations, auto precharge is disabled.
During READ bursts, the valid data-out element from the starting column address will
be available following the CL after the READ command. Each subsequent data-out
element will be valid by the next positive clock edge. Figure 11 on page 22 shows general
timing for each possible CL setting.
Upon completion of a burst, assuming no other commands have been initiated, the DQs
will go High-Z. A full-page burst will continue until terminated. (At the end of the page, it
will wrap to column 0 and continue.)
Data from any READ burst may be truncated with a subsequent READ command, and
data from a fixed-length READ burst may be immediately followed by data from a READ
command. In either case, a continuous flow of data can be maintained. The first data
element from the new burst follows either the last element of a completed burst or the
last desired data element of a longer burst which is being truncated.
The new READ command should be issued x cycles before the clock edge at which the
last desired data element is valid, where x = CL -1. This is shown in Figure 12 on page 23
for CL = 2 and CL = 3; data element n + 3 is either the last of a burst of four or the last
desired of a longer burst. The 64Mb SDRAM uses a pipelined architecture and therefore
does not require the 2n rule associated with a prefetch architecture. A READ command
can be initiated on any clock cycle following a previous READ command. Full-speed
random read accesses can be performed to the same bank, as shown in Figure 13 on
page 24, or each subsequent READ may be performed to a different bank.
COMMAND
CLK
t
RCD (MIN) When 2 <
ACTIVE
T0
T1
NOP
t
RCD
21
t
RCD (MIN)/
T2
NOP
Micron Technology, Inc., reserves the right to change products or specifications without notice.
t
READ or
CK ≤ 3
WRITE
T3
DON’T CARE
64Mb: x4, x8, x16 SDRAM
T4
©2000 Micron Technology, Inc. All rights reserved.
Commands