MAXQ610-KIT# Maxim Integrated, MAXQ610-KIT# Datasheet - Page 6

• Manufacturer Part Number: MAXQ610-KIT#
• Description: Development Boards & Kits - Other Processors MAXQ610 Eval Kit
• Manufacturer: Maxim Integrated

Specifications of MAXQ610-KIT#

• Rohs: yes
• Part # Aliases: 90-M6100#KIT

Table 1. Jumper Functions
MAXQ610 Evaluation Kit
The MAXQ610 EV kit board provides eight momentary
contact switches intended for user input. Each switch is
connected to a separate port pin on the MAXQ610’s
port 1 (P1.7–P1.0) as illustrated in Table 2. The other
side of each switch is connected to ground. Therefore,
by using the weak pullup capability of the port pins,
switch closure can be detected by reading a low on the
normally high corresponding port pin.
6
NAME
JH14
JH15
JH16
JH17
JH18
JH20
JH21
JH22
JH23
JH24
JH25
JH26
JH1
JH2
JH3
JH4
JH5
_______________________________________________________________________________________
Connects pin 3 (FORCEON) of the RS-232 level translator U1 to:
Connects pin 4 (
Connects T1IN (pin 7) of the RS-232 level translator U1 to:
Connects T2IN (pin 8) of the RS-232 level translator U1 to:
Connects the board’s VDD source to:
Connects the MAXQ610’s VDD supply input (pin 38) to the board’s VDD source.
Connects the board’s D1 LED IR emitter to the MAXQ610’s IRTX pin (pin 39).
Connects the board’s D2 LED IR receiver amplified signal to the MAXQ610’s IRRX pin (pin 40).
Connects the IR Rx enable to the MAXQ610’s P0.7 pin (pin 10).
Connects pin 2 (
Connects R1OUT (pin 9) of the RS-232 level translator U1 to the MAXQ610’s port pin P0.1 input (RX0, pin 3).
Connects R2OUT (pin 10) of the RS-232 level translator U1 to the MAXQ610’s port pin P0.3 input (RX1, pin 6).
Connects the board’s DS1 LED cathode to the MAXQ610’s port pin P3.0 (pin 2).
Connects the board’s DS2 LED cathode to the MAXQ610’s port pin P3.1 (pin 4).
Connects the board’s DS3 LED cathode to the MAXQ610’s port pin P3.2 (pin 15).
Connects the board’s DS4 LED cathode to the MAXQ610’s port pin P3.3 (pin 16).
Connects the board’s V50 source to the VCC5 pin of the JTAG connector (pin 8) allowing the JTAG board to source
the 5V power.
Pin 1 to 2: MAXQ610 port pin P3.5 (pin 28)
Pin 2 to 3: The board’s VDD
Pin 1 to 2: MAXQ610 port pin P3.6 (pin 33)
Pin 2 to 3: The board’s VDD
Pin 1 to 2: The board’s VDD
Pin 2 to 3: MAXQ610 port pin P0.2 (TX0, pin 5)
Pin 1 to 2: The board’s VDD
Pin 2 to 3: MAXQ610 port pin P0.4 (TX1, pin 7)
Pin 1 to 2: U2’s regulated 3.3V out (pin 5)
Pin 2 to 3: GND
User Input Pushbuttons
) of the RS-232 level translator U1 to the MAXQ610’s port pin P3.4 (pin 27).
) of the RS-232 level translator U1 to:
DESCRIPTION
Table 2. Switch Input Connections
PORT PIN
P1.0
P1.1
P1.2
P1.3
P1.4
P1.5
P1.6
P1.7
SWITCH
SW2
SW3
SW4
SW5
SW6
SW7
SW8
SW9