MAX98089EVKIT+TQFN Maxim Integrated, MAX98089EVKIT+TQFN Datasheet - Page 113
MAX98089EVKIT+TQFN
Manufacturer Part Number
MAX98089EVKIT+TQFN
Description
Audio IC Development Tools
Manufacturer
Maxim Integrated
Type
Audio CODECr
Datasheet
1.MAX98089EVKITTQFN.pdf
(131 pages)
Specifications of MAX98089EVKIT+TQFN
Product
Evaluation Kits
Tool Is For Evaluation Of
MAX98089
Operating Supply Voltage
2.8 V to 5.5 V
Interface Type
I2C
Operating Supply Current
1 A
- Current page: 113 of 131
- Download datasheet (4Mb)
The IC includes extensive click-and-pop reduction cir-
cuitry. The circuitry minimizes clicks and pops at turn-on,
turn-off, and during volume changes.
Zero-crossing detection is implemented on all analog
PGAs and volume controls to prevent large glitches when
volume changes are made. Instead of making a volume
change immediately, the change is made when the audio
signal crosses the midpoint. If no zero-crossing occurs
within the timeout window, the change is forced.
Volume slewing breaks up large volume changes into the
smallest available step size and the steps through each
step between the initial and final volume setting. When
Table 30. Click-and-Pop Reduction Register
Maxim Integrated
REGISTER
0x47
BIT
7
6
5
1
0
Click-and-Pop Reduction
EQ2EN
EQ1EN
VS2EN
NAME
ZDEN
VSEN
Enhanced Volume Smoothing
During volume slewing, the controller waits for each step in the ramp to be applied be-
fore sending the next step. When zero-crossing detection is enabled this prevents large
steps in the output volume when no zero crossings are detected.
0 = Enabled
1 = Disabled
Applies to volume changes in HPVOLL, HPVOLR, RECVOL, SPVOLL, and SPVOLR.
Volume Adjustment Smoothing
Volume changes are smoothed by stepping through intermediate steps. Also ramps
the volume from minimum to the programmed value at turn-on and back to minimum at
turn-off.
0 = Enabled
1 = Disabled
Applies to volume changes in HPVOLL, HPVOLR, RECVOL, SPVOLL, and SPVOLR.
Zero-Crossing Detection
Holds volume changes until there is a zero crossing in the audio signal. This reduces
click and pop during volume changes (zipper noise). If no zero crossing is detected
within 100ms, the volume change is forced.
0 = Enabled
1 = Disabled
Applies to volume changes in PGAM1, PGAM2, PGAOUTA, PGAOUTB, PGAOUTC,
HPVOLL, HPVOLR, RECVOL, SPVOLL, and SPVOLR.
See the 5-Band Parametric EQ section.
Low-Power, Stereo Audio Codec
with FlexSound Technology
enabled, volume slewing also occurs at device turn-on
and turn-off. During turn-on the volume is set to mute
before the output is enabled. Once the output is on, the
volume ramps to the desired level. At turn-off the volume
is ramped to mute before the outputs are disabled.
When there is no audio signal zero-crossing detection
can prevent volume slewing from occurring. Enable
enhanced volume slewing to prevent the volume control-
ler from requesting another volume level until the previ-
ous one has been set. Each step in the volume ramp then
occurs after a zero crossing has occurred in the audio
signal or the timeout window has expired. During turn-off,
enhance volume slewing is always disabled.
DESCRIPTION
MAX98089
113
Related parts for MAX98089EVKIT+TQFN
Image
Part Number
Description
Manufacturer
Datasheet
Request
R
Part Number:
Description:
Low-power, Stereo Audio Codec With Flexsound Technology
Manufacturer:
Maxim Integrated Products, Inc.
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 1.25Gbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Single +5V, fully integrated, 155Mbps laser diode driver.
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
MAX7528KCWPMaxim Integrated Products [CMOS Dual 8-Bit Buffered Multiplying DACs]
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
VRD11/VRD10, K8 Rev F 2/3/4-Phase PWM Controllers with Integrated Dual MOSFET Drivers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Highly Integrated Level 2 SMBus Battery Chargers
Manufacturer:
Maxim Integrated Products
Datasheet:
Part Number:
Description:
Current Monitor and Accumulator with Integrated Sense Resistor; ; Temperature Range: -40°C to +85°C
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TSSOP 14/A°/RS-485 Transceivers with Integrated 100O/120O Termination Resis
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
QFN 16/A°/AC-DC and DC-DC Peak-Current-Mode Converters with Integrated Step
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
TDFN/A/65V, 1A, 600KHZ, SYNCHRONOUS STEP-DOWN REGULATOR WITH INTEGRATED SWI
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
Integrated Temperature Controller f
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
SOT23-6/I°/45MHz to 650MHz, Integrated IF VCOs with Differential Output
Manufacturer:
Maxim Integrated Products
Part Number:
Description:
EVALUATION KIT/2.4GHZ TO 2.5GHZ 802.11G/B RF TRANSCEIVER WITH INTEGRATED PA
Manufacturer:
Maxim Integrated Products