AT25DF161-SSH-B Atmel, AT25DF161-SSH-B Datasheet - Page 30

• Manufacturer Part Number: AT25DF161-SSH-B
• Description: IC FLASH 16MBIT 100MHZ 8SOIC
• Manufacturer: Atmel

Specifications of AT25DF161-SSH-B

• Format - Memory: FLASH
• Memory Type: DataFLASH
• Memory Size: 16M (2M x 8)
• Speed: 100MHz
• Interface: SPI, RapidS
• Voltage - Supply: 2.7 V ~ 3.6 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Density: 16Mb
• Access Time (max): 5ns
• Interface Type: Serial (SPI)
• Boot Type: Not Required
• Address Bus: 1b
• Operating Supply Voltage (typ): 3.3V
• Operating Temp Range: -40C to 85C
• Package Type: SOIC
• Program/erase Volt (typ): 2.7 to 3.6V
• Sync/async: Synchronous
• Operating Temperature Classification: Industrial
• Operating Supply Voltage (min): 2.7V
• Operating Supply Voltage (max): 3.6V
• Word Size: 8b
• Number Of Words: 2M
• Supply Current: 19mA
• Mounting: Surface Mount
• Pin Count: 8
• Mounting Style: SMD/SMT
• Memory Configuration: 8192 Pages X 256 Bytes
• Clock Frequency: 100MHz
• Supply Voltage Range: 2.7V To 3.6V
• Memory Case Style: SOIC
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant

11.
11.1
Table 11-1.
Notes:
30
Bit
3:2
7
6
5
4
1
0
(1)
Status Register Commands
Read Status Register
The two-byte Status Register can be read to determine the device’s ready/busy status, as well as the status of many other
functions such as Hardware Locking and Software Protection. The Status Register can be read at any time, including during
an internally self-timed program or erase operation.
To read the Status Register, the CS pin must first be asserted and the opcode of 05h must be clocked into the device. After
the opcode has been clocked in, the device will begin outputting Status Register data on the SO pin during every
subsequent clock cycle. After the second byte of the Status Register has been clocked out, the sequence will repeat itself
starting again with the first byte of the Status Register as long as the CS pin remains asserted and the clock pin is being
pulsed. The data in the Status Register is constantly being updated, so each repeating sequence will output new data. The
RDY/BSY status is available for both bytes of the Status Register and is updated for each byte.
At clock frequencies above f
operating at clock frequencies above f
the correct values of both bytes of the Status Register.
Deasserting the CS pin will terminate the Read Status Register operation and put the SO pin into a high-impedance state.
The CS pin can be deasserted at any time and does not require that a full byte of data be read.
1. Only bit 7 of Status Register Byte 1 will be modified when using the Write Status Register Byte 1 command
2. R/W = Readable and writeable
RDY/BSY
Atmel AT25DF161
SPRL
WPP
SWP
WEL
RES
EPE
R = Readable only
Status Register Format – Byte 1
Sector Protection Registers Locked
Reserved for future use
Erase/Program Error
Write Protect (WP) Pin Status
Software Protection Status
Write Enable Latch Status
Ready/Busy Status
Name
CLK
, the first two bytes of data output from the Status Register will not be valid. Therefore, if
CLK
, at least four bytes of data must be clocked out from the device in order to read
Type
R/W
R
R
R
R
R
R
(2)
00
01
10
11
0
1
0
0
1
0
1
0
1
0
1
Sector Protection Registers are unlocked (default).
Sector Protection Registers are locked.
Reserved for future use.
Erase or program operation was successful.
Erase or program error detected.
WP is asserted.
WP is deasserted.
All sectors are software unprotected (all Sector
Protection Registers are 0).
Some sectors are software protected. Read individual
Sector Protection Registers to determine which sectors
are protected.
Reserved for future use.
All sectors are software protected (all Sector Protection
Registers are 1 – default).
Device is not write enabled (default).
Device is write enabled.
Device is ready.
Device is busy with an internal operation.
Description
3687E–DFLASH–11/10