CY7C1370D-167AXC Cypress Semiconductor Corp, CY7C1370D-167AXC Datasheet - Page 12

• Manufacturer Part Number: CY7C1370D-167AXC
• Description: IC SRAM 18MBIT 167MHZ 100LQFP
• Manufacturer: Cypress Semiconductor Corp
• Type: Synchronousr

Specifications of CY7C1370D-167AXC

• Memory Size: 18M (512K x 36)
• Package / Case: 100-LQFP
• Format - Memory: RAM
• Memory Type: SRAM - Synchronous
• Speed: 167MHz
• Interface: Parallel
• Voltage - Supply: 3.135 V ~ 3.6 V
• Operating Temperature: 0°C ~ 70°C
• Access Time: 3.4 ns
• Maximum Clock Frequency: 167 MHz
• Supply Voltage (max): 3.6 V
• Supply Voltage (min): 3.135 V
• Maximum Operating Current: 275 mA
• Organization: 128 K x 16
• Maximum Operating Temperature: + 70 C
• Minimum Operating Temperature: 0 C
• Mounting Style: SMD/SMT
• Number Of Ports: 4
• Operating Supply Voltage: 3.3 V
• Memory Configuration: 1M X 18 / 512K X 36
• Clock Frequency: 167MHz
• Supply Voltage Range: 3.135V To 3.6V
• Memory Case Style: TQFP
• No. Of Pins: 100
• Rohs Compliant: Yes
• Density: 18Mb
• Access Time (max): 3.4ns
• Sync/async: Synchronous
• Architecture: SDR
• Clock Freq (max): 167MHz
• Operating Supply Voltage (typ): 3.3V
• Address Bus: 19b
• Package Type: TQFP
• Operating Temp Range: 0C to 70C
• Supply Current: 275mA
• Operating Supply Voltage (min): 3.135V
• Operating Supply Voltage (max): 3.6V
• Operating Temperature Classification: Commercial
• Mounting: Surface Mount
• Pin Count: 100
• Word Size: 36b
• Number Of Words: 512K
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant, Lead free / RoHS Compliant
• Other names: 428-2135; CY7C1370D-167AXC

IEEE 1149.1 Serial Boundary Scan (JTAG)
The CY7C1370D/CY7C1372D incorporates a serial boundary
scan test access port (TAP). This part is fully compliant with
1149.1. The TAP operates using JEDEC-standard 3.3V or 2.5V
I/O logic levels.
The CY7C1370D/CY7C1372D contains a TAP controller,
instruction register, boundary scan register, bypass register, and
ID register.
Disabling the JTAG Feature
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(V
nally pulled up and may be unconnected. They may alternately
be connected to V
left unconnected. Upon power-up, the device will come up in a
reset state which will not interfere with the operation of the
device.
TAP Controller State Diagram
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
Test Access Port (TAP)
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs are
captured on the rising edge of TCK. All outputs are driven from
the falling edge of TCK.
Test Mode Select (TMS)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to leave
this ball unconnected if the TAP is not used. The ball is pulled up
internally, resulting in a logic HIGH level.
Document Number: 38-05555 Rev. *K
SS
1
0
) to prevent clocking of the device. TDI and TMS are inter-
TEST-LOGIC
RUN-TEST/
RESET
IDLE
0
1
DD
through a pull-up resistor. TDO should be
1
0
CAPTURE-DR
UPDATE-DR
PAUSE-DR
DR-SCA N
SHIFT-DR
EXIT1-DR
EXIT2-DR
1
SELECT
0
0
1
0
1
1
0
1
1
0
0
1
0
CAPTURE-IR
UPDATE-IR
PAUSE-IR
1
IR-SCAN
SHIFT-IR
EXIT1-IR
EXIT2-IR
SELECT
0
0
1
0
1
1
0
1
1
0
0
Test Data-In (TDI)
The TDI ball is used to serially input information into the registers
and can be connected to the input of any of the registers. The
register between TDI and TDO is chosen by the instruction that
is loaded into the TAP instruction register. TDI is internally pulled
up and can be unconnected if the TAP is unused in an appli-
cation. TDI is connected to the most significant bit (MSB) of any
register. (See Tap Controller Block Diagram.)
Test Data-Out (TDO)
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current state
of the TAP state machine. The output changes on the falling edge
of TCK. TDO is connected to the least significant bit (LSB) of any
register. (See Tap Controller State Diagram.)
TAP Controller Block Diagram
Performing a TAP Reset
A Reset is performed by forcing TMS HIGH (V
edges of TCK. This Reset does not affect the operation of the
SRAM and may be performed while the SRAM is operating.
At power-up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
TAP Registers
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test circuitry.
Only one register can be selected at a time through the
instruction register. Data is serially loaded into the TDI ball on the
rising edge of TCK. Data is output on the TDO ball on the falling
edge of TCK.
Instruction Register
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the TDI
and TDO balls as shown in the Tap Controller Block Diagram.
Upon power-up, the instruction register is loaded with the
IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as described
in the previous section.
TM S
TCK
TDI
Selection
Circuitry
CY7C1370D, CY7C1372D
Boundary Scan Register
Identification Register
31
x
Instruction Register
TAP CONTROLLER
30
.
Bypass Register
29
.
.
.
.
.
.
.
2
2
2
1
1
1
0
0
0
0
Selection
Circuitry
DD
) for five rising
Page 12 of 29
TDO
[+] Feedback