M95256-WMN6P STMicroelectronics, M95256-WMN6P Datasheet - Page 11

• Manufacturer Part Number: M95256-WMN6P
• Description: IC EEPROM 256KBIT 5MHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M95256-WMN6P

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 256K (32K x 8)
• Speed: 5MHz
• Interface: SPI, 3-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Organization: 32 K x 8
• Interface Type: SPI
• Maximum Clock Frequency: 5 MHz
• Access Time: 60 ns
• Supply Voltage (max): 6.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 5 mA
• Maximum Operating Temperature: + 130 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Memory Configuration: 32K X 8
• Ic Interface Type: Serial, SPI
• Clock Frequency: 20MHz
• Supply Voltage Range: 2.5V To 5.5V
• Memory Case Style: SOIC
• No. Of Pins: 8
• Rohs Compliant: Yes
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-6357-5; M95256-WMN6P

M95256-DR, M95256, M95256-W, M95256-R
3.8.3
4
4.1
therefore recommended to connect the S line to V
Figure
In addition, the Chip Select (S) input offers a built-in safety feature, as the S input is edge
sensitive as well as level sensitive: after power-up, the device does not become selected
until a falling edge has first been detected on Chip Select (S). This ensures that Chip Select
(S) must have been High, prior to going Low to start the first operation.
The V
defined in
Power-down
During Power-down (continuous decrease of V
operating voltage defined in
●
●
Operating features
Hold condition
The Hold (HOLD) signal is used to pause any serial communications with the device without
resetting the clocking sequence.
During the Hold condition, the Serial Data output (Q) is high impedance, and Serial Data
input (D) and Serial Clock (C) are Don’t Care.
To enter the Hold condition, the device must be selected, with Chip Select (S) low.
Normally, the device is kept selected, for the whole duration of the Hold condition.
Deselecting the device while it is in the Hold condition, has the effect of resetting the state of
the device, and this mechanism can be used if it is required to reset any processes that had
been in progress.
The Hold condition starts when the Hold (HOLD) signal is driven low at the same time as
Serial Clock (C) already being low (as shown in
The Hold condition ends when the Hold (HOLD) signal is driven high at the same time as
Serial Clock (C) already being low.
Figure 5
with Serial Clock (C) being low.
deselected (Chip Select S should be allowed to follow the voltage applied on V
in Standby Power mode (there should not be an internal Write cycle in progress).
CC
17).
also shows what happens if the rising and falling edges are not timed to coincide
voltage has to rise continuously from 0 V up to the minimum V
Table
8,
Table 9
and
Table
Doc ID 12276 Rev 11
Table 10
8,
Table 9
and the rise time must not vary faster than 1 V/µs.
and
CC
Figure
Table
CC
supply voltage below the minimum V
via a suitable pull-up resistor (see
5).
10), the device must be:
CC
Operating features
operating voltage
CC
)
11/48
CC