M24256-BWMN6TP STMicroelectronics, M24256-BWMN6TP Datasheet - Page 17

• Manufacturer Part Number: M24256-BWMN6TP
• Description: IC EEPROM 256KBIT 400KHZ 8SOIC
• Manufacturer: STMicroelectronics

Specifications of M24256-BWMN6TP

• Format - Memory: EEPROMs - Serial
• Memory Type: EEPROM
• Memory Size: 256K (32K x 8)
• Speed: 400kHz
• Interface: I²C, 2-Wire Serial
• Voltage - Supply: 2.5 V ~ 5.5 V
• Operating Temperature: -40°C ~ 85°C
• Package / Case: 8-SOIC (3.9mm Width)
• Density: 256Kb
• Interface Type: Serial (I2C)
• Organization: 32Kx8
• Access Time (max): 900ns
• Frequency (max): 400KHz
• Write Protection: Yes
• Data Retention: 40Year
• Operating Supply Voltage (typ): 3.3/5V
• Package Type: SOIC
• Operating Temp Range: -40C to 85C
• Supply Current: 5mA
• Operating Supply Voltage (min): 2.5V
• Operating Supply Voltage (max): 5.5V
• Operating Temperature Classification: Industrial
• Mounting: Surface Mount
• Pin Count: 8
• Maximum Clock Frequency: 0.4 MHz
• Access Time: 900 ns
• Supply Voltage (max): 5.5 V
• Supply Voltage (min): 2.5 V
• Maximum Operating Current: 5 mA
• Maximum Operating Temperature: + 85 C
• Mounting Style: SMD/SMT
• Minimum Operating Temperature: - 40 C
• Operating Supply Voltage: 2.5 V, 5.5 V
• Lead Free Status / RoHS Status: Lead free / RoHS Compliant
• Other names: 497-8623-2; M24256-BWMN6TP

M24256-BF, M24256-BR, M24256-BW, M24256-DR
3.9
3.10
3.11
Identification Page Write (M24256-DR only)
The Identification page is written by issuing an ID Write instruction. This instruction uses the
same protocol and format as the Page Write in memory array, except for the following
differences:
●
●
If the Identification page is locked, the data bytes transferred during the Identification Page
Write instruction are not acknowledged (NoAck).
Lock Identification Page (M24256-DR only)
The Lock Identification Page instruction (Lock ID) permanently locks the Identification page
in read-only mode. The Lock ID instruction is similar to Byte Write (into memory array) with
the following specific conditions:
●
●
●
If the Identification Page is locked, the data bytes transferred during the ID Write instruction
are not acknowledged (NoAck).
ECC (error correction code) and write cycling
The M24256-Bx and M24256-DRdevices offer an ECC (error correction code) logic which
compares each 4-byte word with its six associated ECC EEPROM bits. As a result, if a
single bit out of 4 bytes of data happens to be erroneous during a Read operation, the ECC
detects it and replaces it by the correct value. The read reliability is therefore much improved
by the use of this feature.
Note however that even if a single byte has to be written, 4 bytes are internally modified
(plus the ECC bits), that is, the addressed byte is cycled together with the other three bytes
making up the word. It is therefore recommended to write by word (4 bytes) in order to
benefit from the larger amount of Write cycles.
The M24256-Bx and M24256-DR devices are qualified at 1 million (1 000 000) Write cycles,
using a cycling routine that writes to the device by multiples of 4-bytes.
Device Type Identifier = 1011b
MSB address bits A15/A6 are don't care except for address bit A10 which must be ‘0’.
LSB address bits A5/A0 define the byte address inside the identification page.
Device Type Identifier = 1011b
Address bit A10 must be ‘1’; all other address bits are don't care
The data byte must be equal to the binary value xxxx xx1x, where x is don't care.
Doc ID 6757 Rev 21
Device operation
17/42