M24C32-RMB6TG STMicroelectronics, M24C32-RMB6TG Datasheet - Page 8
![IC EEPROM 32KBIT 400KHZ 8UFDFPN](/photos/7/23/72351/m24c32-rmb6tg_sml.jpg)
M24C32-RMB6TG
Manufacturer Part Number
M24C32-RMB6TG
Description
IC EEPROM 32KBIT 400KHZ 8UFDFPN
Manufacturer
STMicroelectronics
Specifications of M24C32-RMB6TG
Format - Memory
EEPROMs - Serial
Memory Type
EEPROM
Memory Size
32K (4K x 8)
Speed
400kHz
Interface
I²C, 2-Wire Serial
Voltage - Supply
1.8 V ~ 5.5 V
Operating Temperature
-40°C ~ 85°C
Package / Case
8-MLP, 8-UFDFPN
Organization
4 K x 8
Interface Type
I2C
Maximum Clock Frequency
0.4 MHz
Access Time
900 ns
Supply Voltage (max)
5.5 V
Supply Voltage (min)
1.8 V
Maximum Operating Current
0.8 mA
Maximum Operating Temperature
+ 85 C
Mounting Style
SMD/SMT
Minimum Operating Temperature
- 40 C
Operating Supply Voltage
2.5 V, 3.3 V, 5 V
Memory Configuration
4096 X 8
Clock Frequency
400kHz
Supply Voltage Range
1.8V To 5.5V
Memory Case Style
DFN
No. Of Pins
8
Rohs Compliant
Yes
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Other names
497-8705-2
M24C32-RMB6TG
M24C32-RMB6TG
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
M24C32-RMB6TG
Manufacturer:
ST
Quantity:
7 489
Signal description
2
2.1
2.2
2.3
2.4
8/38
Signal description
Serial Clock (SCL)
This input signal is used to strobe all data in and out of the device. In applications where this
signal is used by slave devices to synchronize the bus to a slower clock, the bus master
must have an open drain output, and a pull-up resistor must be connected from Serial Clock
(SCL) to V
most applications, though, this method of synchronization is not employed, and so the pull-
up resistor is not necessary, provided that the bus master has a push-pull (rather than open
drain) output.
Serial Data (SDA)
This bidirectional signal is used to transfer data in or out of the device. It is an open drain
output that may be wire-OR’ed with other open drain or open collector signals on the bus. A
pull up resistor must be connected from Serial Data (SDA) to V
the value of the pull-up resistor can be calculated).
Chip Enable (E0, E1, E2)
These input signals are used to set the value that is to be looked for on the three least
significant bits (b3, b2, b1) of the 7-bit device select code. These inputs must be tied to V
or V
floating), these inputs are read as low (0,0,0).
Figure 3.
Write Control (WC)
This input signal is useful for protecting the entire contents of the memory from inadvertent
write operations. Write operations are disabled to the entire memory array when Write
Control (WC) is driven high. When unconnected, the signal is internally read as V
Write operations are allowed.
When Write Control (WC) is driven high, device select and Address bytes are
acknowledged, Data bytes are not acknowledged.
SS
, to establish the device select code as shown in
CC
Device select code
.
(Figure 4
indicates how the value of the pull-up resistor can be calculated). In
Doc ID 4578 Rev 17
E i
M24xxx
V CC
V SS
E i
M24xxx
V CC
V SS
Ai12806
Figure
M24C32-W M24C32-R M24C32-F
3. When not connected (left
CC
.
(Figure 4
indicates how
IL
, and
CC