IS42S16800D-7TL ISSI, Integrated Silicon Solution Inc, IS42S16800D-7TL Datasheet - Page 26
![IC SDRAM 128MBIT 143MHZ 54TSOP](/photos/7/23/72310/is42s16800d-7tl_sml.jpg)
IS42S16800D-7TL
Manufacturer Part Number
IS42S16800D-7TL
Description
IC SDRAM 128MBIT 143MHZ 54TSOP
Manufacturer
ISSI, Integrated Silicon Solution Inc
Datasheet
1.IS42S16800D-7TL.pdf
(62 pages)
Specifications of IS42S16800D-7TL
Package / Case
54-TSOP II
Memory Size
128M (8Mx16)
Format - Memory
RAM
Memory Type
SDRAM
Speed
143MHz
Interface
Parallel
Voltage - Supply
3 V ~ 3.6 V
Operating Temperature
0°C ~ 70°C
Data Bus Width
16 bit
Maximum Clock Frequency
143 MHz
Access Time
6.5 ns, 5.4 ns
Supply Voltage (max)
3.6 V
Supply Voltage (min)
3 V
Maximum Operating Current
130 mA
Maximum Operating Temperature
+ 70 C
Minimum Operating Temperature
0 C
Mounting Style
SMD/SMT
Lead Free Status / RoHS Status
Lead free / RoHS Compliant
Lead Free Status / RoHS Status
Lead free / RoHS Compliant, Lead free / RoHS Compliant
Other names
706-1020
Available stocks
Company
Part Number
Manufacturer
Quantity
Price
Company:
Part Number:
IS42S16800D-7TL
Manufacturer:
ISSI
Quantity:
20
Company:
Part Number:
IS42S16800D-7TL
Manufacturer:
ISSI
Quantity:
240
Part Number:
IS42S16800D-7TL
Manufacturer:
ISSI
Quantity:
20 000
Company:
Part Number:
IS42S16800D-7TLI
Manufacturer:
ISSI
Quantity:
1 000
Part Number:
IS42S16800D-7TLI
Manufacturer:
ISSI
Quantity:
20 000
CAS LATENCY
IS42S81600D,
CAS Latency
The CAS latency is the delay, in clock cycles, between the
registration of a READ command and the availability of the
first piece of output data. The latency can be set to two or
three clocks.
If a READ command is registered at clock edge n, and the
latency is m clocks, the data will be available by clock edge
n + m. The DQs will start driving as a result of the clock edge
one cycle earlier (n + m - 1), and provided that the relevant
access times are met, the data will be valid by clock edge
n + m. For example, assuming that the clock cycle time is
such that all relevant access times are met, if a READ
command is registered at T0 and the latency is programmed
to two clocks, the DQs will start driving after T1 and the data
will be valid by T2, as shown in CAS Latency diagrams. The
Allowable Operating Frequency table indicates the operat-
ing frequencies at which each CAS latency setting can be
used.
Reserved states should not be used as unknown operation or
incompatibility with future versions may result.
26
IS42S16800D
COMMAND
COMMAND
CLK
CLK
DQ
DQ
READ
READ
T0
T0
CAS Latency - 2
NOP
NOP
CAS Latency - 3
T1
T1
t
LZ
t
AC
CAS Latency
Operating Mode
The normal operating mode is selected by setting M7 and M8
to zero; the other combinations of values for M7 and M8 are
reserved for future use and/or test modes. The programmed
burst length applies to both READ and WRITE bursts.
Test modes and reserved states should not be used
because unknown operation or incompatibility with future
versions may result.
Write Burst Mode
When M9 = 0, the burst length programmed via M0-M2
applies to both READ and WRITE bursts; when M9 = 1, the
programmed burst length applies to READ bursts, but write
accesses are single-location (nonburst) accesses.
Speed
-75E
NOP
NOP
Allowable Operating Frequency (MHz)
T2
T2
-6
-7
Integrated Silicon Solution, Inc. — www.issi.com
D
OUT
t
t
OH
LZ
t
AC
NOP
CAS Latency = 2
T3
T3
D
DON'T CARE
UNDEFINED
OUT
t
OH
125
100
133
T4
CAS Latency = 3
166
143
—
07/28/08
Rev. E