DS32506NW Maxim Integrated, DS32506NW Datasheet - Page 130

• Manufacturer Part Number: DS32506NW
• Description: Network Controller & Processor ICs
• Manufacturer: Maxim Integrated

Specifications of DS32506NW

• Part # Aliases: 90-32506-NW0

17.
Maxim/Dallas Semiconductor cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim/Dallas Semiconductor product.
No circuit patent licenses are implied. Maxim/Dallas Semiconductor reserves the right to change the circuitry and specifications without notice at any time.
M a x i m I n t e g r a t e d P r o d u c t s , 1 2 0 S a n G a b r i e l D r i v e , S u n n y v a l e , C A 9 4 0 8 6 4 0 8 - 7 3 7 - 7 6 0 0
REVISION
The Maxim logo is a registered trademark of Maxim Integrated Products, Inc. The Dallas logo is a registered trademark of Dallas Semiconductor Corporation.
062906
091307
040808
103008
DATE
DATA SHEET REVISION HISTORY
Initial data sheet release.
Added Internal Receive Enable (ITRE) pin to
Changed VDD18 tolerance from ± 10% to ± 5%
Added Internal Receive Enable (ITRE) pin description to
Interface Pin Description.
Changed VDD18 tolerance from ± 10% to ± 5%
Descriptions).
In Section 8.2.8, removed “Note that internal termination is only available when a
microprocessor interface is enabled.”
Changed RXP to TXN in the third paragraph of Section 8.2.9: Driver Monitor and
Output Failure Detection .
In Section 8.3.1, removed “Note that internal termination is only available when a
microprocessor interface is enabled.”
Removed Section 8.12: Initialization .
In the Absolute Maximum Ratings section, changed the VDD18 supply range from
”-0.1V to +1.98V” to “-0.1V to +1.89V”.
In
1.89V (max).
In
In
In
In
DS32512, DS32508, and DS32506 hardware-interface-only pin assignments.
In
not exist on the DS32506). Changed pins A10, A11, B10, B11, F11, and G11 to N.C.
Changed pins C11, D11, E11, G10, R9, and V4 to VSS.
In Section 9.7, clarified register bit text descriptions for LINE.RSR:BPVC and
LINE.RSR:EXCZ.
Table
Table
Table 11-2
Table
Figure
Figure 12-8
11-1, changed VDD18 from 1.62V (min) to 1.71V (min) and 1.98V (max) to
11-2, changed all I
12-1, added ITRE to ball R10.
12-2,
to
(left half), corrected typos where some pins for port 7 were listed (do
Figure
Table
12-5, and
11-10, changed VDD18 tolerance from ± 10% to ± 5%.
DD18
© 2008 Maxim Integrated Products
, I
Figure
DD33
DESCRIPTION
, I
130 of 130
DDTTS18
12-8, changed ball R10 from N.C. to ITRE for
Table 7-1
, and I
(Table 7-1
(Table 7-10
DDTTS33
. Short Pin Descriptions.
Table 7-5
. Short Pin Descriptions).
. Power-Supply Pin
typ and max values.
. Hardware
DS32506/DS32508/DS32512
CHANGED
93, 94, 96,
111, 117,
103, 105
PAGES
97, 98,
106
123
123
14
15
20
23
25
26
30
48
92
93
83
—